background image

2

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all 

safety messages.

This is the safety alert symbol. 
This symbol alerts you to potential hazards that can kill or hurt you and others. 
All safety messages will follow the safety alert symbol and either the word “DANGER” or 
“WARNING.” These words mean:

You can be killed or seriously injured if you don’t  

immediately follow instructions.
You can be killed or seriously injured if you don’t 

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you 

what can happen if the instructions are not followed.

Important Safety Instructions

CAUTION: 

Hydrogen gas is produced in a hot water system served by this heater that has not been used for a long 

period of time (2 weeks or more).  Hydrogen gas is extremely flammable. To reduce the risk of injury under these 

conditions, it is recommended that the hot water faucet be opened for several minutes at the kitchen sink before 

using any electrical appliance connected to the hot water system. When hydrogen is present, there will probably be 

an unusual sound such as air escaping through the pipe as the water begins to flow. There should be no smoking or 

open flame near the faucet at the time it is open.

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of 

substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires 

businesses to warn of potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or other 

reproductive harm. 
This appliance can cause low-level exposure to some of the substances included in the Act.

WATER HEATER SAFETY

IMPORTANT:

 The heat pump portion of this water heater uses R-134a refrigerant. See the data plate on the heat pump 

jacket for the charge level.

Содержание Premier























Отзывы: