manualshive.com logo in svg

State Water Heaters GS 6, Инструкция по установке и эксплуатации

Поделиться
Скачать
State Water Heaters GS 6 Скачать руководство пользователя страница 26

trap (sometimes called a dirt leg) must be incorporated in 
the piping. The sediment trap must be readily accessible. 
Install in accordance with the “Gas Piping” section. Refer to 
the current edition of the 

National Fuel Gas Code (ANSI 

Z223.1/NFPA 5 4)

.

HOT-WATER 

OUTLET

COLD-

WATER 

INLET

UNION

TEMPERATURE-
PRESSURE 
RELIEF VALVE

DISCHARGE PIPE
(DO NOT CAP 
OR PLUG)

6” MAX. AIR GAP 
BELOW DISCHARGE 
PIPE

METAL 
DRAIN 
PAN

FLOOR
DRAIN

DRAIN
VALVE

SHUT-OFF VALVE

SOME 

COMPONENTS 

NOT SHOWN 

FOR CLARITY.

SIDE TAP 
(OUTLET)

SIDE TAP 
(INLET)

Figure 27.  

 FILLING THE WATER HEATER

•

 Avoid water heater damage.

•

 Fill tank with water before operating.

Property Damage Hazard

CAUTION

• 

Do not insert the power cord into the electrical 
receptacle until the heater has been fully installed.

• 

Never use this water heater unless it is completely full 
of water. To prevent damage to the tank, the tank must 
be 

fi

 lled with water. Water must 

fl

 ow from the hot-water 

faucet before turning “ON” gas to the water heater.

To 

fi

 ll the water heater with water:

1.  Close the water heater drain valve by turning handle 

to the right (clockwise). The drain valve is on the lower 
front of water heater (see Figure 27).

2.  If the heater is equipped with plumbing side taps and 

they are not connected to piping, ensure that the side 
taps have been closed with pipe plugs.

3.  Open all hot-water faucets served by the water heater 

to allow air to escape from the tank and the water 
piping. Ensure any shut-off valves between the heater 
and the faucets are the open position.

4.  Open the cold-water supply valve to the water heater.

Notes:

 

•  The cold-water supply valve must be left open when 

the water heater is in use.

  •  Avoid water leakage when 

fi

 lling the tank. Do not 

allow the insulation of the water heater to get wet as 
water can reduce the effectiveness of the insulation.

5.  To ensure complete 

fi

 lling of the tank, allow air to exit 

by opening nearest hot-water faucet. Allow water to 
run until a constant 

fl

 ow is obtained. This will let air 

out of the water heater and the piping.

6.  Check all water piping and connections for leaks. 

Repair as needed.

 VENTING

Breathing carbon monoxide can cause brain damage or death.

Always read and understand instruction manual.

•

 Install vent system In accordance with codes.

•

 Do not operate water heater if flood damaged.

•

 Install water heater in accordance with the 

instruction manual.

•

 Do not operate if soot buildup is present.

•

 Do not obstruct water heater air intake(s) with 

insulating blanket.

•

 Do not place chemical vapor emitting products near 

water heater.

•

 Gas and carbon monoxide detectors are available.

•

 Never operate the heater unless it is vented to the 

outdoors and has adequate air supply to avoid risks 
of improper operation, fire, explosion or asphyxia-
tion.

•

 Analyze the entire vent system to make sure that 

condensate will not become trapped in a section of 
vent pipe and therefore reduce the open cross 
sectional area of the vent.

Breathing Hazard - Carbon Monoxide Gas

WARNING

Important:

 DO NOT common vent this water heater with 

any power vented appliance. DO NOT vent into a common 
chimney.

26 www.statewaterheaters.com 

Содержание GS 6





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды