StarTech.com 8STPEXSAT34RH Скачать руководство пользователя страница 25

Страница: 25 / 28

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

View Properties of your Physical Hard Drives

•

Select your desired physical disk from list of Physical Disks in

the Marvell Storage Menu. The Property tab is now displayed,

listing the Properties for your disk.

Property tab

Note:

Your physical disk properties cannot be edited.

Erase Foreign RAID Configuration

Warning!

When erasing previously configured RAID Data,

this enclosure will erase all drive data. Please be aware

that any data currently on the drives will be lost during this

process. It is recommended that you back up all data prior to

erasing previously configured RAID data.

RAID controllers store data on any drive within a RAID array. If

your drives have been previously configured in a different RAID

array, this data must be deleted before a new array can be built.

Please follow the below steps to erase previously configured

RAID data.

Select your desired physical disk from list of Physical Disks in

Содержание 8STPEXSAT34RH





























Результаты поиска

Содержание 8STPEXSAT34RH

Отзывы:

Похожие инструкции для 8STPEXSAT34RH

Бренды по названию

Популярные бренды

StarTech.com 8STPEXSAT34RH, Руководство пользователя

Результаты поиска

Содержание 8STPEXSAT34RH

Отзывы:

Похожие инструкции для 8STPEXSAT34RH

Бренды по названию

Популярные бренды