background image

Part Number: 3601 / 3651 

 Page 6 

Version 1.0 

© 2019 Starkey Products, Inc.  

Trouble shooting guide: 
Fog lights won’t turn ON –  

 

Check to make sure you connected the red posi-lock connector to the correct wire outlined in the 
“Installing switch in passenger compartment” section above. This is the MOST common mistake 
made during installation. If you cut the wrong wire, do not panic, contact us to provide another 
posi-lock connector which makes re-connecting it easy.  

 

Check to make sure your vehicle is in the Accessory or ON mode (Start button green LED is 
blinking or solid). 

 

Check the ground cable you connected under the “Wiring in engine bay” section. Make sure that it 
is making proper contact and that the bolt is tightened.  

 

Check the ring terminal you connected to the side of the fuse box to +12v power. Make sure that it 
is making proper contact and that the bolt is tightened.  

 

Check the blue fuse installed in the fuse holder (small black box located on orange wire). Make 
sure it is plugged in completely and has not been blown (On a blown fuse the filament in the 
middle of the two posts has been broken). 

 
Fog lights stay ON –  

 

Check to make sure you installed the red posi-lock connector on the proper wire outlined in the 
“Installing switch in passenger compartment” section above. If you connected your wire tap to the 
wrong wire, it may result in the fog lights staying on until you shut off the vehicle. If you cut the 
wrong wire, do not panic, contact us to provide another posi-lock connector which makes re-
connecting it easy. 

 

If the fog lights turn ON and OFF normally with the fog light button, but do not shut off when the 
vehicle is turned off, check the red wire connected to the 5 amp fuse under the engine bay fuse 
box. Be sure you have connected the red wire to the proper 5 amp fuse slot.  

 
If you are still having trouble with your product, please contact us for technical assistance. Tech support is 
available via phone Monday through Friday 9am-5pm. Email tech support is available during regular 
business hours as well as weekends, holidays, and evenings. 
 

Starkey Products, Inc. 
Phone:

 (386)-951-6335 

Email:

 

[email protected]

 

Website:

 

www.Starkey-Products.com

 

 

Limited Warranty: 

This warranty covers defects in materials or workmanship in any component sold by Starkey Products, Inc. or its authorized 
dealers. Warranty is effective for five years from the date of purchase. Coverage terminates if you sell or transfer ownership of 
the product. Starkey Products will repair or replace the defective or malfunctioning product or any defective or malfunctioning 
part thereof at no charge. This warranty covers parts and labor only. This warranty does not cover any problem that is caused 
by abuse, misuse, acts of God, or improper installation. Any modification or alteration to any component will void the product 
warranty. Warranty does not cover wear that any components receive through the normal course of operation and use 
(including but not limited to bulbs). All warranty claims require proof of purchase. 

 

Содержание 3601







Отзывы: