background image

Part Number: 3601 / 3651 

 Page 1 

Version 1.0 

© 2019 Starkey Products, Inc.  

 

2018-2019 Ford Mustang Ecoboost OEM-Style Fog Light Kit 

Parts List: 

Quantity: 

 

Tool List: 

LED Foglight Assemblies  

 

 

Flat head & Phillips screwdriver 

(if you ordered part#3601) 

 

 

 

Ratchet & Socket set OR 

Wiring harness 

 

 

Adjustable Wrench 

Ford OEM Switch 

 

 

Wire stripping tool or razor blade 

PB-3601 Parts Bag 

 

 

Thank you for purchasing one of our products. Please familiarize yourself with the parts included as well 
as the instructions before attempting installation. Please seek the help of a certified technician if you feel 
unable to complete the installation safely and properly. Failure to read and follow the instructions below 
may result in personal injury or damage to property. Starkey Products, Inc. and our retailers assume no 
liability for failures to comply with guidelines and warnings outlined in this instruction manual.  
 
If you are receiving this instruction manual with part #3651 (Starkey Fog Light Wiring & Switch Kit), 
skip to the ‘Wiring in Engine Bay’ section on page 2. Otherwise, begin steps immediately below. 
 
Fog light installation into bumper: 

Removing the bumper is not necessary. Driving the vehicle onto ramps or raising the front end of the 
car will greatly ease installation. Before beginning the steps below, turn off the car, remove key, and 
engage the emergency brake.  

1.

 

Open hood of car and make sure hood is held open securely.  

2.

 

Removing the air deflector will allow you access to fog light mounting points. The air deflector is 
held on by 17 screws and 2 push pins (shown as dots in picture 1 below). Use a ratchet & 7mm 
socket OR wrench to remove the screws. The pins are removed with a flat head screwdriver - pry 
up on center part of the pin and then pry up on the body of the pin. See picture 2.  

3.

 

Use flathead screwdriver to remove the 3 lower push pins in each wheel well. These push pins 
help support the air deflector. Save for re-installation later. The deflector is removed by pulling 
back/ down gently. Set aside hardware and deflector for re-attachment later.  

4.

 

Unplug connectors on each lamp.  

5.

 

Remove 3 screws holding each lamp assembly in place and carefully remove lamp assembly. See 
picture 3.  

6.

 

Install new lamp. Re-use 3 mounting screws.   

 

 

 

 

Remove air deflector. It is held on 
by 17 screws/ 2 push pins. 

Pry up on center part of pin first. 
Then pry out entire push pin. 

Unplug wiring & remove 3 
screws holding lamp on. 

Содержание 3601







Отзывы: