background image

Page 7

GUIDE ROD LUBRICATION:

1.

Apply a general purpose lubricant (such 
as 3-in-1 oil) that does not contain Teflon 
to a cotton cloth, then run the cotton 
cloth up and down the guide rods as 
needed. 

2.

Also apply oil to the incremental weight 
guide tracks.

3.

Verify that the Top Plate and Incremental 
Plate slide smoothly.

Incremental 

Guide Track

Guide Rod

M8 Jam Nut (2X)           

Frame

No Gap

Washer

REAR FOOT ADJUSTMENT:

1.

Verify that the equipment is at the 
desired location and then check to make 
sure the feet contact the ground and 
leveled.

2.

If the machine rocks or is tippy, adjust 
rear foot by loosening the two Nyloc nuts 
using a 13MM open-end wrench and a 
6MM hex key.

3.

Slide the foot up or down until the 
machine is leveled.

4.

Re-tighten the bolts and nuts.

TOP PLATE & CABLE ADJUSTMENT:

1.

Engage                          pin at maximum 
weight and actuate arm 3 to 4 times to 
fully seat the weight stacks.

2.

Disengage                          pins and 
verify that there is no gap between the 
Top Plate and the lower weight plate.  If 
a gap exists or if there is too much slack 
on the cable, then the cable tension 
needs to be adjusted. 

3.

Using two 13MM open end wrench, 
loosen the upper M8 Jam Nuts. Adjust 
cable tension until the Top Plate drops 
and rests on to the weight stack. 

4.

Hand tighten the jam nuts and check to 
make sure the gap is gone.  Cable 
should deflect no more than ±25mm 
from centerline without raising the Top 
Plate.  Check for smooth                      
pin engagement.

5.

Tighten jam nuts.

Содержание INSPIRATION STRENGTH IP-S6331













Отзывы: