Star Trac Elite CrossTrainer Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 43

background image

CrossTrainer Service Manual

26

CrossTrainer Service Manual Rev A 620-7575

Part Inst. Procedure - LCB, Batt. And UB Board (cont.)

Install the New UB Board

1. Use the short Phillips head screwdriver to install the two screws to hold the UB board to the

frame.

2. Connect the two wires to the board.

3. Before installing the UB shroud panel, test for functionality.

Reinstall the LCB Plastic Shield

1. Position the LCB Shield over the electronics and align the holes for the plastic thumb screws.

2. Tighten the screws.

Reinstall the Upper Body Shroud

1. Carefully reinsert the upper body shroud onto the frame.

2. Reinstall the 6 screws that hold the UB shroud to the unit.

«
...
25
26
27
28
29
...
»

Содержание Elite CrossTrainer












































Отзывы:

Нет отзывов

Похожие инструкции для Elite CrossTrainer

Бренд: Doufit Страницы: 13

Бренд: True Fitness Страницы: 2

PROGRAMMABLE ELLIPTICAL TRAINER

Бренд: Hsumao Страницы: 15

Бренд: FLOWFITNESS Страницы: 68

VECTOR ABDOMINAL FLEXION

Бренд: ERGO-FIT Страницы: 104

Alliance ET920D

Бренд: Keys Fitness Страницы: 12

Бренд: Weslo Страницы: 16

Бренд: Weslo Страницы: 16

Momentum R 4.2 Elliptical

Бренд: Weslo Страницы: 20

Momentum G 3.8 Elliptical

Бренд: Weslo Страницы: 20

Бренд: Weslo Страницы: 24

460 Variable Stride Elliptical

Бренд: Schwinn Страницы: 87

CROSSTRAINER X100

Бренд: Monark Страницы: 32

Бренд: Insportline Страницы: 13

Бренд: Insportline Страницы: 18

Бренд: Insportline Страницы: 18

Бренд: Insportline Страницы: 17

Бренд: Insportline Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды