Star Trac Elite CrossTrainer Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 43

background image

CrossTrainer Service Manual

19

CrossTrainer Service Manual Rev A 620-7575

Part Installation Procedure - Shrouds (cont.)

3.  Use the Phillips screwdriver to remove the 5 UB shrouds screws.
4.  Slide the shroud off the frame.
5.  Repeat step 1-4 on the right UB shroud panel.

Remove the Lower Body Shroud

1. Use the 5/16 Allen (hex) key to remove the bolt holding the lower linkage arm to the crank.

Note: Weight and movement of leg beam will
force the lower linkage to move in the forward
direction during removal. Either have another
person hold the leg beam or pedal in position;
use a block under the pedal.

2. Use the Phillips screwdriver to remove the 2 screws holding the center shroud cover.

«
...
18
19
20
21
22
...
»

Содержание Elite CrossTrainer












































Отзывы:

Нет отзывов

Похожие инструкции для Elite CrossTrainer

Бренд: habitat et jardin Страницы: 18

NordicTrack STUDIO ELLIPTICAL

Бренд: ICON Health & Fitness Страницы: 36

Бренд: NordicTrack Страницы: 24

Бренд: Sunny Health & Fitness Страницы: 8

Navarre Elite Elliptical

Бренд: Yowza Страницы: 41

Бренд: Body Rider Страницы: 24

Pro-Form Endurance 320 E

Бренд: ICON Health & Fitness Страницы: 28

Бренд: Fortis Страницы: 10

Бренд: Christopeit Sport Страницы: 60

OrbiTrek OR1000-PRO

Бренд: Thane Fitness Страницы: 9

Бренд: Tunturi Страницы: 60

Бренд: Tunturi Страницы: 66

Бренд: Pro-Form Страницы: 28

Бренд: Pro-Form Страницы: 28

220 Zle Elliptical

Бренд: Pro-Form Страницы: 24

Бренд: Pro-Form Страницы: 24

Бренд: Pro-Form Страницы: 28

Бренд: Pro-Form Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды