Star-Oddi DST microRF-HRT Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 42

Star-Oddi DST microRF-HRT Скачать руководство пользователя страница 19

User Manual

Gná Graphic Supporting Software

©Star-Oddi 2015. All Rights Reserved

Page 19

6.

RF box and antenna

The antenna receives signals from the logger and transmits them to the RF box. The

RF box then transmits the data to the Personal Area Network (PAN).

Each cage will need a set of antenna and RF box. The antenna is attached to the

bottom of the cage using, for example, Velcro

®

and then connected to the RF box (see

figure 6.1). The RF box can also be attached to the cage using Velcro

®

Figure 6.1 RF box and antenna

The RF box can work on battery power alone, the box is charged using the power

supply that comes with the box.

6.1

Starting & running

Connect the antenna to the RF box and switch the box on. The green light will stay on

for 5 seconds after the box has been switched on.

Once the RF box has been connected it will appear on the RF box table on the left

side of the interface. The table also shows how much battery is left in the RF box and

when the battery status was last updated (see figure 6.2). The RF box table can be

cleared by selecting View-Clear RF-Box Battery.

Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com (603) 746-5524

«
...
17
18
19
20
21
...
»

Содержание DST microRF-HRT











































Отзывы:

Нет отзывов