ENGLISH
(Original instructions)
4
ADDITIONAL POWER TOOL SAFETY WARNINGS
Safety warnings for heat guns
• A fire may result if the appliance is not used with care,
therefore
- Be careful when using the appliance in places where
there are combustible material
- Do not apply to the same place for long time
- Do not use in presence of an explosive atmosphere
- Be aware that heat may be conducted to combustible
materials that are out of sight
- Place the appliance on site after use and allow it to
cool down before storage
- Do not leave the appliance unattended when it
is switched on.
• Always switch off before putting tool down.
• Extreme care should be taken when stripping paint,
the peelings, residue and vapors of paint may contain
lead, which is poisonous. Once deposited on surfaces,
hand to mouth contact can result in the ingestion of lead.
Exposures to even low levels of lead can caused
irreversible brain and nervous system damage; young and
unborn children are particularly vulnerable. Do not smoke,
eat or drink in a work area that could or may be
contaminated by lead.
Lead based paints should only
be removed by a professional and should not be
removed using a heat gun.
• When removing paints you should ensure that your
work area is enclosed.
It is advisable to wear a dust
mask.
• Do not burn the paint.
Keep the nozzle at least 25mm
(1”) from the surface as this keeps the temperature below
the required 450°C. If you are scraping from a vertical
position then you should scrape downwards to prevent the
paint from falling back into the heat gun and burning.
Dispose of all paint debris safely and ensure that the work
area is thoroughly cleaned after completing the job.
• Do not use in a damp atmosphere or where flammable
gases may be present
or use near combustible materials.
Spaces behind boards, ceilings and floors and wall
cavities in timber frame constructed houses can contain
flammable materials. Check before using the heat gun.
• Allow the tool to cool fully before storing.
• Ensure adequate ventilation
when using heat guns as
toxic fumes may be produced.
• Do not use as a hairdryer!
The air temperature is far
higher than a hairdryer.
• Do not obstruct
either the air intake or nozzle outlet as
this may cause excessive heat build up resulting in
damage to the tool.
• Do not direct the hot air blast at other people.
• Do not touch the metal nozzle
as it becomes very hot
during use and remains hot for up to 30 minutes after use.
Do not look down the nozzle while the unit is working
because of the high temperatures being produced.
• Do not allow paint to adhere
to the nozzle or scraper as
it could ignite after a time.
• Do not operate your heat gun
whilst it is hanging by the
hanging hook.
• A fire may arise if the appliance is not used with care.
• Do not place the nozzle against anything while using
or immediately after use.
• Do not poke anything down the nozzle as it could give
you an electric shock.
SAFETY OF OTHERS
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety.
• Children should be supervised to ensure that they do not
play with the appliance.
RESIDUAL RISKS
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
• Injuries caused by touching any rotating/moving parts.
• Injuries caused when changing any parts, blades or
accessories.
• Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
• Impairment of hearing.
• Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
ELECTRICAL SAFETY
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
WARNING!
If the power cord is damaged, it must be
replaced by the manufacturer, authorized STANLEY
Service Center or an equally qualified person in
order to avoid damage or injury. If the power cord is
replaced by an equally qualified person, but not
authorized by STANLEY, the warranty will not be
valid.
