Stanley STGS7221, Руководство пользователя, Страница: 12 / 14

12 • ENGLISH
sliding the plastic opening of the bag down over the dust
exhaust port of the sander as shown in FIG. 7. To empty
the dust bag, remove it from the sander and unzip the bag
over a trash container.
Warning! Fire hazard. Collected sanding dust from
sanding surface coatings (polyurethane, linseed oil,
etc.) can self-ignite in sander dust bag or elsewhere
and cause fire. To reduce risk, empty bag frequently and
strictly follow sander manual and coating manufacturer’s
instructions.
Warning! Fire hazard. When working on metal
surfaces, do not use the dust bag or a vacuum cleaner
because sparks are generated. Wear safety glasses
and a dust mask. Due to the danger of fire, do not use
your belt sander to sand magnesium surfaces. Do not use
for wet sanding.
OPERATION
Using your belt sander (FIG. I)
Always hold belt sander firmly with both hands while
sanding as shown in FIG. I.
Note: that sander bail handle can be adjusted to three
different positions as previously discussed.
Switch (FIG. J & K)
To start your belt sander, depress the on/off switch as
shown in FIG. J. To stop your belt sander release the on/
off switch.
For continuous operation, depress the on/off switch then
depress the lock-on button (FIG. K) and release the on/off
switch. To stop your belt sander, depress the on/off switch
to release the lock-on button. Release the on/off switch.
Handy Hints
f
Always start your belt sander before it is in contact
with the workpiece and do not switch it off until after it
has been lifted from the workpiece.
f
Always hold your belt sander with two hands.
f
Where possible, clamp the workpiece to a work bench
or similar sturdy surface.
f
Use the correct grit sanding belt for your application.
The following is a suggested list of belt grits to use
with different materials.
MATERIAL BELT GRIT
Solid Wood 80
Veneer 150
Chipboard 60/80
Plastics 100
Steel 80 (remove dust bag)
Paint Removal 40/60
Balsa Wood 100
Acrylic 100
Tool Care And Maintenance
Your tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Never apply excessive force when you use your belt
sander. Too much force can result in an overload and
cause damage to the motor or the workpiece. If your belt
sander becomes too hot, operate it without load for 2
minutes. Always keep the air cooling vents clear. To clean
your belt sander, proceed as follows:
Warning! To prevent accidental operation, turn off and
unplug sander before performing the following operations.
Failure to do this could result in serious personal injury.
f
Use a clean dry paint brush to clear vents and ducts.
f
Clean the housings using a clean damp cloth (do not
use solvents, gas or turpentine.)
Important! To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
should be performed by authorized service centers or
other qualified service personnel, always using identical
replacement parts.
ACCESSORIES
The performance of your tool depends on the accessory
used. Stanley accessories are engineered to high quality
standards and designed to enhance the performance of
your tool. By using these accessories you will get the very
best from your tool.
Use only 3” x 21” (76 x 533mm) sanding belts. Recommended
accessories for use with your tool are available at extra
cost from your local dealer or authorized service center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley
product needs replacement, or if it is of no
further use to you, do not dispose of it with
household waste. Make this product available for
separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials. Local regulations may
provide for separate collection of electrical
products from the household, at municipal waste
sites or by the retailer when you purchase a new
product.