7
ENGLISH (
Original Instructions)
Tool Care
Avoid overloading the machine.Overloading will result in a
considerable reduction in speed and efficiency and the unit
will become hot. In this event,run the machine at no load for
a minute or two until cooled to normal working temperature
by the built in fan. Switching your machine on and off whilst
under load will considerably reduce the life of the switch.
Important
To ensure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (other than those listed in this
manual) should be performed by authorized service centers
or other qualified organizations, always-using identical
replacement parts. Unit contains no user serviceable parts
inside.Blowing dust and grit out of the main housing by
means of an air hose is recommended and may be done as
often as dirt is seen collecting in and around the air vents.
Always wear proper eye and respiratory protection.
Accessories
The performance of your tool depends on the accessory
used. STANLEY accessories are engineered to high quality
standards and designed to enhance the performance of
your tool. By using these accessories you will get the very
best from your tool.
MAINTENANCE
Your STANLEY/tool has been designed to operate over
a long period of time with a minimum of maintenance. To
ensure satisfactory operations, the tool must be maintained
and cleaned regularly
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing accessories,
before adjusting or changing set-ups or when making
repairs.
Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
♦ This machine is not user-serviceable. If problems occur
contact an authorised repair agent.
WARNING!
Before performing any maintenance:
♦ Switch off and unplug the tool.
♦ Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Lubrication
Stanley power tools are properly lubricated at the
factory and are ready for use. Tools should be re-
lubricated regularly , depending on usage. This
lubrication should only be attempted by trained
power tool repair persons, such as those at
Stanley service centers or by other qualified service
personnel.
Cleaning
Warning:
unplug the tool before you use a cloth to
clean the housing.With the motor running, blow
dirt and dust out of all air vents with dry air at least
once a week. Wear safety glasses when
performing this. Exterior plastic parts may be cleaned with a
damp cloth and mild detergent. Although these parts are
highly solvent resistant, NEVER use solvents.
Blowing dust and grit out of the main housing by
means of an air hose is recommended and may
be done as often as dirt is seen collecting in and
around the air vents. Always wear proper eye
and respiratory protection.
ACCESSORIES
The performance of any power tool is dependent upon the
accessory used. Stanley accessories areengineered to
high quality standards and are designed to enhance the
performance of power tool.
Note:
Accessory must be rated for use at speed equal to
or higher than nameplate RPM of tool with which it is being
used.
Protecting The Environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Please sort it out for
separate recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
STANLEY provides a facility for the collection and recycling
of STANLEY products once they have reached the end of
their working life. To take advantage of this service please
return your product to any authorised repair agent who will
collect them on our behalf.
You can check the location of your nearest authorised
repair agent by contacting your local STANLEY office at
the address indicated in this manual. Alternatively, a list
of authorised STANLEY repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com
Notes
STANLEY’s policy is one of continuous improvement to
our products and as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local STANLEY dealers for range
availability.
