background image

6.

THE FLAME FAILURE DEVICE

6.1

This is a safety feature incorporated in all 
WATERFORD fires which automatically 
switches off the gas supply if the pilot 
light goes out  and fails to heat the thermo-
couple.

7.

'RUNNING IN'

7.1

The surface coating on the coals used in 
your WATERFORD fire will "burn off" dur-
ing the first few hours of use, producing a 
harmless and temporary odour.  This will 
disappear after a short period of use.  If 
the odour persists, ask your installer for 
advice.

8.

SERVICING

8.1

The fire must be serviced every 12 
months by a qualified Gas Engineer.  In all
correspondence, always quote the appli-
ance type and the serial number, which 
may be found on the data badge.

9.

ENAMEL CLEANING

General cleaning must be carried out when the
stove is cool.

If this stove is finished in a high gloss vitreous
enamel, to keep the enamel in the best condition
observe the following tips:

9.1

Wipe over daily with a soapy damp cloth, 
followed by a polish with a clean dry 
duster.

9.2

For stubborn deposits a soap impregnated
pad can be carefully used on the vitreous 
enamel.

9.3

Use only products recommended by the 
Vitreous Enamel Association, these prod-
ucts carry the vitramel label.

9.4

DO NOT USE ABRASIVE PADS OR 
OVEN CLEANSERS CONTAINING CIT
RIC ACID ON ENAMELLED SURFACES.
ENSURE THAT THE CLEANSER MANU
FACTURERS INSTRUCTIONS ARE 
ADHERED TO.

3

ASSOCIATION

Содержание MAEVE

















Отзывы: