Stanley FATMAX KFFMEG841, Оригинальное руководство пользователя

Страница: 8 / 72

8
ENGLISH (Original instructions)
Voltage drops
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected.
If the system impedance of the power supply is lower than
0.107 Ω, disturbances are unlikely to occur.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Side handle
4. Spindle lock
5. Guard
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (fig. A)
The tool is supplied with a guard intended for grinding
purposes only. If the unit is intended to perform cutting off
operations, a guard specific for this operation must be fitted.
A suitable guard for cutting off operations part numbers
1004484-02 is available and can be obtained from Stanley Fat
Max service centres.
Fitting
u
Place the tool on a table, with the spindle (6) facing up.
u
Release the clamping lock (7) and hold the guard (5) over
the tool as shown.
u
Align the lugs (8) with the notches (9).
u
Press the guard down and rotate it counterclockwise to
the required position.
u
Fasten the clamping lock (7) to secure the guard to the
tool.
u
If required, tighten the screw (10) to increase the clamping
force.
Removing
u
Release the clamping lock (7).
u
Rotate the guard clockwise to align the lugs (8) with the
notches (9).
u
Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u
Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. B - D)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u
Fit the guard as described above.
u
Place the inner flange (11) onto the spindle (6) as shown
(fig. B). Make sure that the flange is correctly located on
the flat sides of the spindle.
u
Place the disc (12) onto the spindle (6) as shown (fig. B).
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
u
Make sure that the disc locates correctly on the inner
flange.
u
Place the outer flange (14) onto the spindle. When fitting
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. C). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. C).
u
Keep the spindle lock (3) depressed and tighten the outer
flange using the two-pin spanner (15) (fig. D).
Removing
u
Keep the spindle lock (4) depressed and loosen the outer
flange (14) using the two-pin spanner (15) (fig. D).
u
Remove the outer flange (14) and the disc (12).
Fitting and removing sanding discs (fig. D & E)
For sanding, a backing pad is required. The backing pad is
available from your Stanley Fat Max dealer as an accessory.
Fitting
u
Place the inner flange (11) onto the spindle (5) as shown
(fig. E). Make sure that the flange is correctly located on
the flat sides of the spindle.
u
Place the backing pad (16) onto the spindle.
u
Place the sanding disc (17) onto the backing pad.
u
Place the outer flange (14) onto the spindle with the raised
centre facing away from the disc.
u
Keep the spindle lock (3) depressed and tighten the outer
flange using the two-pin spanner (15) (fig. D). Make sure
that the outer flange is fitted correctly and that the disc is
clamped tightly.
Removing
u
Keep the spindle lock (4) depressed and loosen the outer
flange (14) using the two-pin spanner (15) (fig. D).
u
Remove the outer flange (14), the sanding disc (17) and
the backing pad (16).