Stanley EA08, Безопасность, эксплуатация и обслуживание

Страница: 9 / 12

EA08 User Manual | 9
helper before starting the tool.
4. Steady the tool and position the auger bit 90° to the ground.
5. Stand with your feet shoulder width apart.
Note: Hold the tool correctly and be ready to counteract normal or sudden
movements. Have both hands available. High reaction torque can develop if
the tool stalls, which can be caused by excessive loads being applied to the
drill bit, by the drill snagging on the material being drilled into or by the drill
bit breaking through the material being drilled.
Tool Activation - Detail E
1. Ensure the auger bit is 90° to the ground.
2. Raise the auger bit above the ground.
Note: Never operate the tool if you cannot be sure that underground utilities
are not present, such as electrical cables, gas pipes, etc. These can cause a
hazard if damaged with the tool.
3. Fully squeeze the trigger.
Note: Always fully squeeze the trigger during operation. Operating the tool
with a slightly depressed trigger increases the hydraulic pressure and can
result in unexpected kickback.
4. Slowly lower the auger bit to the ground.
5. After reaching the desired depth, release the trigger.
Note: If you encounter a breakdown or the tool stops for any reason, release
the trigger and power down the hydraulic power source.
6. Squeeze the reverse trigger to reverse the auger bit.
7. Lift the auger straight out of the hole and release the trigger. Ensure the
auger bit has stopped before the tip of the bit reaches the surface.
Tool Use Tips
• On soft ground, EA08 will penetrate the ground easily and may require
you to apply a slight lift to the tool handles.
• On hard ground, you may need to apply slight down pressure on the
tool handles.
• During operation, frequently lift the auger to clear dirt and debris from
the hole.
Tool Maintenance
Use only accessories, consumables and parts recommended by STANLEY.
Do not perform maintenance while the hydraulic power
source is connected. Accidental engagement of the tool
can cause serious injury. Disconnect the hydraulic power
source before performing maintenance.
Daily Maintenance
1. Remove hydraulic power from the tool.
2. Check all hydraulic connections and hoses for damage. Replace
damaged parts before operating the tool.
3. Inspect the bit retainer and associated parts. Replace when they have
become worn, cracked or distorted.
4. Check all fasteners for tightness. Pay particular attention to the bolts
holding the handles and torque tube in place. Re-torque if necessary.
5. Inspect tool to ensure all decals are legible. Contact STANLEY if
replacements are needed.
6. Using a calibrated flow and pressure gauge, check the output of the
hydraulic power source. Ensure it matches the flow and pressure in
“Specifications” on page 8. Proper flow and pressure maintain
proper tool speed.
Tool Storage & Transport
Drain the tool of hydraulic fluid and plug open hydraulic ports. Collect all
hydraulic fluid for recycling (See “Tool Disposal” on page 9). Clean the
tool and store in a clean, dry space that is safe from damage. Ensure the tool
is secured and will not move during transport. An unsecured tool could cause
personal injury or damage to the tool.
Tool Disposal
Hydraulic Oil
Hydraulic oil can contaminate the air, ground and water if not properly
recycled. Recycle hydraulic oil in accordance with all State, Federal and local
laws, at your local oil recycling facility.
Hydraulic Hoses
Hang hydraulic hoses to drain. Collect the oil for recycling. Contact your local
municipal recycling authorities for an approved hydraulic hose recycling site.
Tool Body
Drain hydraulic oil from the tool, making sure to collect the oil for recycling.
Disassemble the tool and dispose of all non-metal parts. Recycle the metal
components. Contact your local municipal recycling authorities for recycling
instructions.
Accessories
EA08 Accessories
Description
Part Number
Coupler, 13/16 Inch x 1 3/8 Inch 58585
Coupler, 1 1/8 Inch x 1 3/8 Inch 58586
Coupler, 1 1/4 Inch 65477
Auger, 2 Inch Ø x 42 Inch overall length (Requires
coupler 58585)
47406
Auger, 3 Inch Ø x 42 Inch overall length (Requires
coupler 58586)
47407
Auger, 4 Inch Ø x 42 Inch overall length 47408
Auger, 6 Inch Ø x 42 Inch overall length 47409
Auger, 8 Inch Ø x 42 Inch overall length 47410
Auger, 10 Inch Ø x 42 Inch overall length 47411
Auger, 12 Inch Ø x 42 Inch overall length 47412
Auger, 16 Inch Ø x 42 Inch overall length 47413
Auger, 18 Inch Ø x 42 Inch overall length 47414
Center Screw, 2 Inch 47430
Center Screw, 3 Inch 47431
Center Screw, 4 Inch 47432
Digging Tooth with Hardface 47429
Troubleshooting
Problem Possible Cause Solution
EA08 doesn’t run, runs
slowly or has poor
performance.
Hydraulic power source
is not running properly.
Ensure the power
source is delivering
proper flow and
pressure. See
“Specifications” on
page 8. Proper
flow and pressure
maintain proper tool
speed. Check regularly.
Hydraulic fluid
restriction.
Ensure hydraulic fluid is
50°F or higher.
Inspect hydraulic
system for blockage.
Pressure and return
hoses are reversed.
See “Connect to
a Hydraulic Power
Source” on page 8.
Hydraulic fluid is too
hot.
Provide cooler to
maintain proper fluid
temperature.
High back pressure.
See “Specifications”
on page 8 and
ensure hydraulic circuit
back pressure is within
listed specification.