Stanford Research Systems SR830 Скачать руководство пользователя страница 127

Страница: 127 / 177

6-10

Performance Tests

b) Press

[Sensitivity Up/Dn]

Select the sensitivity from the table.

c) Wait for the R reading to stabilize. Record the value of R for each sensitivity.

4) Frequency response is checked at frequencies above 1 kHz. The test frequencies are listed below.

Test Frequencies

24 kHz
48 kHz
72 kHz
96 kHz

a) Set the AC calibrator to 1 kHz and an amplitude of 200.00 mVrms.

b) Set the frequency synthesizer to 1 kHz.

c) Press

[Sensitivity Up/Dn]

Set the sensitivity 200 mV.

d) Set the AC calibrator and frequency synthesizer to the frequency in the table.

e) Wait for the R reading to stabilize. Record the value of R.

f) Repeat steps 4d and 4e for all of the frequencies listed.

5) This completes the amplitude accuracy and frequency response test. Enter the results of this test in

the test record at the end of this section.

Содержание SR830


















































































































































































Результаты поиска

Содержание SR830

Отзывы:

Похожие инструкции для SR830

Бренды по названию

Популярные бренды

Stanford Research Systems SR830, Руководство пользователя

Результаты поиска

Содержание SR830

Отзывы:

Похожие инструкции для SR830

Бренды по названию

Популярные бренды