background image

LIGHTING INSTRUCTIONS 

 
HDMG Griddles are furnished with either a pilot safety valve or a standing pilot (not available in the European 
Community). Please follow the instructions for your unit. HMG Griddles are furnished with either a flame failure 
pilot or a standing pilot (not available in the European community). 

Pilot Operation HMG Flame Failure Gas Valve:  

Operation on the gas valve pilot.

 

1.  Turn knob on the main gas valve to the pilot position.  

2.  Depress knob to start gas flow to the pilot valve.  

3.  Light pilot valve. 

a.  Using a match or taper 

4.  Hold in knob for 15 to 30 seconds to heat up the thermocouple. 

5.  Release knob and turn to the desired gas flow position. 

a.  If pilot goes out repeat steps 1-4, some thermocouples will take longer to heat up 

Standing Pilot Lighting Instructions: 

(Not Available in the European Community) 

The pilot lights on the broilers have been set at the factory. A screwdriver may be required for the first lighting to 
adjust the flame for your elevation. 

1.  Turn off the manual shut off valve and wait 5 minutes to clear the gas. 

2.  Turn all knobs to the "OFF" position. 

3.  The valve can be accessed through an opening in the front panel or remove the cooking grates and light 

the pilot from above. 

4.  Turn the manual shut off valve on. 

5.  Hold  an  ignition  source  (match)  to  both  openings  on  the  pilot  tube.  When  the  flames  are  established, 

remove the ignition source. 

6.  Turn the burner knobs to "HI". If the burner does not ignite, promptly open the pilot valve more. If the pilot 

flame appears larger than necessary, turn it down  and reset burner ignition. The pilot flame should be as 
small as possible but large enough to guarantee reliable ignition of the burners when the knobs are turned 
to "HI". 

RELIGHTING PILOT 

If the pilot light should go out for any reason: 

 

Promptly shut off all gas at the manual shut off valve. 

 

Turn off all knobs and pilot valves; wait 5 minutes to clear gas. 

 

Relight following steps 4 through 6 under Standing Pilot Lighting Instructions. 

HDTG LIGHTING THE MAIN BURNER: 

Since the burner is lit from constantly burning pilot, turn knobs to "HI" to put the unit in operation; then adjust to 
any desired position between "LO" and "HI". 

 

 

To  light  burner,  turn  knob  to  "max."  then  back  off  to  the  desired  flame  level.  The  range  of  adjustment  is 
virtually infinite between high and off. (At the small flame, there is a pre-set low). 

 

When  the  broiler  is  first  heated,  it  will  smoke  until  oil  used  in  manufacturing,  preservation  and  dust  from 
storage and shipping are burned off. An hour at "max." on all burners is usually sufficient. 

 

Turn knobs off and let cool 

Содержание Tri-Star TSHMG-2424i



















Отзывы: