Standard Change-Makers System 500E Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 11

background image

- 11 -

Power Supply- 40 Watt Board Adjustment

NOTE: The power supply is factory adjusted by a trained technician. However, if you
have access to a volt meter, it’s advisable to check the 5.35 DC voltage setting for
accuracy. If required, use the adjusting pot to set the voltage between pin 3 and pin 4 to
5.35 volts. Improperly adjusted or “weak” supplies can cause “power fault” errors or
poor bill acceptance.

5.3VDC

1

6

(+)

(-)

«
...
9
10
11

Содержание System 500E












Отзывы:

Нет отзывов

Похожие инструкции для System 500E

Бренд: Garland Страницы: 32

Бренд: Omron Страницы: 11

Бренд: Wincor Nixdorf Страницы: 28

Бренд: Easson Страницы: 22

Бренд: ICP DAS USA Страницы: 70

Бренд: AccuBANKER Страницы: 20

Бренд: Omron Страницы: 133

Бренд: Omron Страницы: 173

Бренд: Omron Страницы: 254

Walking style One 2.0

Бренд: Omron Страницы: 2

Бренд: Magnescale Страницы: 12

Бренд: Pixsys Страницы: 72

Бренд: ChemoMetec Страницы: 76

Бренд: ATO Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды