Standard Change-Makers System 500E Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 11

background image

- 10 -

Coin Hopper Maintenance

Once a year, you will want to check the inside of your hoppers(s) for pieces of string or
other debris from moneybags or dirty coins. With your power OFF, simply empty the
hopper and take a look inside. If you see any obvious dirt or strings, promptly remove it.
With canned air, blow out the feed mechanism located in the bottom of the hopper
beneath the plastic funnel. Next, open the hopper door and blow air into the gear
assembly area as shown below. Finally, use a clean rag and wipe of the coin interrupter
located above the chute on the inside of the hopper door.

Clean out
Feed Mechanism

Hopper Door

Hopper Door

Clean Out

Closed

Opened

Gear Assembly

HHHHH

«
...
8
9
10
11
»

Содержание System 500E












Отзывы:

Нет отзывов

Похожие инструкции для System 500E

Shelleysteel SCFM-50

Бренд: Delfield Страницы: 2

Бренд: EMKO Страницы: 48

Бренд: BEKA Страницы: 46

Бренд: NanoEnTek Страницы: 40

Бренд: Nautilus Hyosung Страницы: 101

Бренд: GBA Страницы: 25

Бренд: Velleman Страницы: 7

Бренд: AccuBANKER Страницы: 6

Бренд: Crouzet Страницы: 42

Бренд: Met One Instruments Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды