DE
19
EN
EN
DETAILED SETTINGS – when the soldering station and SMD rework station are being
used simultaneously:
1. First press of the button / function knob (9): setting the soldering iron tempera-
ture, „SOLDERING” is blinking – desired value of the temperature can be set by
knob (9). After setting the temperature, the “SOLDERING” stops blinking.
2. Second press of the button / function knob (9): setting the SMD rework gun tem-
perature, „HOT AIR” is blinking – desired value of the temperature can be set by
knob (9). After setting the temperature, the “HOT AIR” stops blinking.
3. Third press of the button / function knob (9): setting the sleep time of the solde-
ring iron. “SLEEP” is blinking, set the desired time by knob (9). Sleep time can be
set between 0 (SLEEP is off) and 99 minutes. When the soldering iron is on, and
not used (placed in the holder), then after a set time, soldering iron will enter into
sleep mode – display will show “SLP”. If the iron will be picked up from the holder,
the device will exit from the sleep mode and enter into working mode – iron will
warms up to a previously set temperature.
4. Fourth press of the button / function knob (9): setting the automatic (AUTO) or
manual (MANUAL) SMD rework gun work mode. The “AUTO” or “MANUAL” on
the display is blinking. Set the desired working mode by knob (9). In manual mode,
SMD rework gun working continuously. In automatic mode, SMD rework gun turns
off when placed into the holder. Chosen “AUTO” or “MANUAL” mode will be
shown on the display.
5. Fifth press of the button / function knob (9): changing the temperature unit (Celsi-
us / Fahrenheit), the
⁰
C or
⁰
F is blinking. Using knob (9) set the desired tempera-
ture unit. Chosen unit will be shown on the display..
6. Sixth press of the button / function knob (9): soldering iron temperature compen-
sation. The “SOLDERING” is blinking, using knob (9) set the desired temperature
compensation value (from -50 to +50). After setting of the desired value the „SOL-
DERING” stops blinking.
7. Seventh press of the button / function knob (9): SMD rework gun temperature
compensation. The “HOT AIR” is blinking, using knob (9) set the desired tempera-
ture compensation value (from -50 to +50). After setting of the desired value the
„HOT AIR” stops blinking.
8. Eight press of the button / function knob (9): saving all above data. The device will
work in accordance with the entered parameters.
Note: both soldering iron and SMD rework gun calibrations of the temperature
were precisely made at the factory. Values of the temperature compensation are pre-
set to 0 and should not be freely adjusted.
Note: Where there is a need to exit from the process of functions setting according
to the above description, after setting the desired parameter, do not press any button
for approx. 5 seconds. The system stores the previously entered data and enters into
normal operation.
MEMORY BUTTONS CH1, CH2, CH3.
Device is equipped with memory buttons for saving entered data CH1, CH2, CH3.
Each button can save any configuration of all working parameters of the device: sol
-
dering iron temperature, SMD reworks gun temperature, working mode of the SMD
rework gun (AUTO or MANUAL), airflow volume, soldering iron sleep time, tempe
-
rature unit.
When all needed parameters are entered, press the button CH1 or CH2 or CH3 for
approx. 3 seconds. After this time, the parameters will be stored under the button
which was pressed. Later, pressing this button will cause immediately operation of the
device with these stored parameters.
GENERAL REMARKS
1. If the display is showing the „---„ it means that the output temperature is lower
than 100
⁰
C, HOT AIR station is in stand by mode, HOT AIR gun is placed in the
holder.
2. If the display is showing “S-E” it means that soldering iron is disconnected, and
HOT AIR gun is having problem with the heat sensor.
3. If the display is showing “F-1” it means that electric circuit of the fan is having
problem.
4. If the display is showing “F-2” it means that the fan is blocked.
5. When the device is being turned on, both soldering iron and HOT AIR gun should
be placed in their holders.
6. The outlet of the HOT AIR gun should be clean and free from any obstacles.
7.
When using small nozzles, it should be remembered that the air flow should be
suitable to the diameter of the fixed nozzle. In order to avoid any HOT AIR gun
damages, too high air flow along with the high temperature mustn’t be used for a
long period of time.
8.
Depending on user’s needs, different air flow settings may cause slight variations
in temperatures value. The minimum distance between the outlet of the HOT AIR
gun and the subject is 2 mm.
9. Good ventilation of the room in which the appliance is used must be provided.
In addition, the device should be placed in a location with good air circulation to
dissipate heat.
SAFETY ISSUES REMARKS
1. Nozzles should be installed without the use of excessive force, also do not use
the pliers or tweezers. Do not over tighten the mounting screws of the nozzle.
2. Tips and nozzles can be changed when the HOT AIR gun and the soldering iron
are completely cold.
3.
It is forbidden to use the device near the flammable or combustible elements
and objects or at similar places. Tips and nozzles as well as the air coming out
of the HOT AIR gun have very high temperature, it is forbidden to touch these
elements as well as it is forbidden to put the hot air directly to face or body. This
can cause serious burns.
18
