Stafford Instruments ST215C Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

Stafford Instruments ST215C Скачать руководство пользователя страница 10

Page

ST215C User Handbook

10

To enter the damper temperature configuration menu press the key and the key

down together while the controller is not running a program (firing indicator not lit).

Note: in the sequence below if no key presses are detected within 30 seconds the

ST215C will exit the menu and damper temperature changes will not be saved.

The damper close temperature prompt is
shown. Release the

&

keys.

Press the

key.

The damper close temperature is now shown.
Adjust with the &

keys (hold down for

acceleration).

Press the

key.

The damper open temperature prompt is now

shown.

Press the

key.

The damper open temperature is now shown.
Adjust with the &

keys (hold down for

acceleration)

Press the

key.

The ST215C will now reset and the new damper control temperatures will be stored.

Note: in the sequence above it is important that the

key is pressed a total of 4

times else changes will not be saved.

Damper Output

Damper Operation

Prior to firing the damper will be open. During firing, when the kiln reaches the damp-

er close temperature, the damper will close. The event indicator will be on.

At the end of the firing and when the kiln has cooled naturally to the damper open

temperature, the damper will open. The event indicator will be off.

Note: The event switch has no function for damper operation

«
...
8
9
10
11
12
...
»

Содержание ST215C

































Отзывы:

Нет отзывов