If wind speed is above the set threshold for at least 15 seconds, an upward movement is activated to protect the awning (wind alarm). During this phase,
all
manual commands are disabled
. The control unit exits the “wind alarm” if the wind speed keeps below the set threshold for at least 5 minutes. The wind
threshold ranges from 5 km/h to 35 km/h. The factory sets the wind threshold at level 2. If two motors are coupled with the anemometer, it is sufficient to operate
a motor only, either by button or remote control, and the settings will be valid also for the second motor.
07.
WIND SENSOR
It is possible to exit the “wind alarm” mode without waiting for the 5 minutes required for the wind to go below the threshold, removing voltage from the device
and waiting a few seconds before switching on again.
07.3 FORCED EXIT FROM THE WIND ALARM
07.2 VISUAL LED SIGNALS ASSOCIATED WITH THE WIND SENSOR
05
RED LED flashing: anemometer in wind alarm mode.
RED + YELLOW LED flashing: anemometer out of order following the “anemometric test” (see paragraph 9)
07.1 CHANGE OF WIND THRESHOLD BY USING A REMOTE CONTROL OR A WALL-MOUNTED BUTTON
01. In the case of multichannel, select the correct radio channel and
move the motor to an intermediate position.
02. Press
MENU
. The motor shows: up/down. Display shows: - - .
03. Press
UP
twice and
DOWN
once. 21 appears on the display.
04. Press
STOP
once. The motor shows: up/down.
05. Press
UP
once. The motor shows the current value by performing 1
to 5 movements (see Table 1).
Factory sets the value on 2.
06. Press the
UP
button a number of times equal to the desired value.
07. The motor performs upward movements equal to the set value.
08. Press
MENU
to exit (the motor does not show anything).
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG. The motor shows: up/down.
03. Press
UP
twice and
DOWN
once.
04. Press
STOP
once. The motor shows up/down
05. Press
UP
once. The motor shows the current value by performing 1 to
5 movements.
(1 = 5km/h; 2 = 10km/h; 3 = 15km/h; 4 = 25km/h; 5 = 35km/h).
Factory sets the value on 2.
06. Press the
UP
button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the
set value.
08. Press
PROG
3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
No. of movements
Threshold
1
2
3
4
5
5 Km/h
10 Km/h
15 Km/h
25 Km/h
35 Km/h
Tab. 01 - Wind threshold
Notes:
1)
The button must be briefly pressed, approx. 1 second between two pressings.
2)
The button must be briefly pressed, approx. 1 second between two pressings. If you do not want to change the setting, wait 15 seconds without pressing
any button.
3) If you try to set a wind threshold higher than 5, the value is rejected and completes 4 short up/down movements.
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press 3 times on
UP
and 3 times on
DOWN
. The motor shows:
up/down.
04. Press
UP
twice and
DOWN
once. The motor shows: up/down.
05. Press
UP
once. The motor shows the current value by performing 1
to 5 movements.
(1 = 5km/h; 2 = 10km/h; 3 = 15km/h; 4 = 25km/h; 5 = 35km/h).
Factory sets the value on 2.
06. Press the
UP
button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the
set value.
08. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
06. HOW TO ADD OR REMOVE A REMOTE CONTROL
After having stored one or more remote controls, it is possible to add other ones by “cloning” the functioning remote controls. It is also possible to eliminate an
already stored and functioning remote control. Proceed as follows.
01. Bring the motor to the intermediate position.
02. Press
PROG
of a remote control already stored, for 5 seconds. Motor makes 2 upward
movements.
03. Within 15 seconds....
to add a remote control: press
STOP
or
UP
on the remote control to be added.
to delete a remote control already stored: press
DOWN
.
04. 2 UP movements: device stored!!
1 DOWN movement: device deleted!!
NOTES:
point 04. “error” is displayed if the radio code does not operate in a timely manner (2 downward movements).
06.1 USING THE REMOTE CONTROL (Only if a remote control is already stored)
With Item 596
With Item 595
PROG
(5 seconds)
01. Bring the motor to the intermediate position.
02. Turn off the power, wait a few seconds, then power up again.
03. Within 15 seconds, briefly and quickly press
UP 3 times
and
DOWN 3 times
. Motor
makes 3 upward movements.
04. Within 15 seconds, briefly and quickly press
UP once
and
DOWN once
.
Motor makes 2 upward movements.
05. Within 15 seconds....
to add a remote control: press
STOP
or
UP
on the remote control to be added.
To delete a remote control: press
DOWN
on the remote control to be deleted.
06. 2 UP movements: device stored!!
1 DOWN movement: device deleted!!
06.2 USING THE COMMAND BUTTONS
3 x UP
3 x DOWN
ON
NOTES:
point 04. “error” is displayed if the radio code does not operate in a timely manner (2 downward movements).
1 x UP
1 x DOWN
