manualshive.com logo in svg

SST Automation GT200-PN-CO, Руководство пользователя, Страница: 29 / 32

Поделиться
Скачать
SST Automation GT200-PN-CO Скачать руководство пользователя страница 29

WWW.SSTAUTOMATION.COM

26

You can see that the IP address of the device has been changed to "192.168.0.188" and the device name has been

changed to "sst-100"

4.5 IP Address Conflict Resolution

According to the specification of PROFINET protocol, acting as a PROFINET slave, GT200-PN-CO must obey

the rule that there can not be more than 1 PROFINET device which has the same IP address and Device name on

the same LAN when connecting many GT200-PN-CO devices.

If the IP address and device name conflict, users can change IP address and device name of GT200-PN-CO

according to

Chapter "4.4.2 Change IP Info and Name"

and make sure that other IP address and name are different

(Notes: after changing is complete, some relevant changes should be taken in PLC modeling and users must

ensure the IP address and name of GT200-PN-CO is the same with that of PLC modeling).

For example:

When IP address conflicts, the IP address, subnet mask and gateway address of GT200-PN-CO will be reset to

"0.0.0.0". Now, users can not use "Upload" or "Download" to scan GT200-PN-CO and only use

Chapter "4.4.1

Scan Devices on LAN"

to scan the device, the scanning result is shown as below:

Содержание GT200-PN-CO

































Отзывы:

Нет отзывов