SSANGYONG Rexton Y200, Руководство пользователя

Страница: 1576 / 1627

SSANGYONG Y200
9D-48 BODY ELECTRICAL
If parking position of wipe motor is not feeding properly
or not, if parking position of wipe motor is not feeding,
wiper motor can be operated quickly rather than the
state of normal, intermittent speed shifting time of wiper
motor is not sensing, wiper motor is not operated
normally.
Notice: While unit of rain sensor is removed.
1. Remove exterior cover, at this time, if exterior cover
is removed by compulsion, keep in mind not to
break fixing hook of coupler, as exterior cover is
removed, using hole of cover by driver, after section
of fixing hook is pushing, and remove them.
2. As rain sensor is removed from coupler, using
driver after open up spring clip, remove them.
3. Remove connector to the wiring from the sensor.
Rear Wiper System
Summary
Controlling of existing rear wiper is controlled by relay
which is operated with switch, but rear wiper of Rexton
is controlled by ECU, in the existing vehicle, brush of
rear wipe is installed on the rear glass, but rear glass
can is opened up, brush of rear wiper can not be
installed, so,this one is installed on the back panel,
wiper motor is operating by second stage.
3. On the turning, Applying the current between
contact point of W of CAM switch and contact point
of C, relay 2 of CONT is “OFF” and relay 1 is
“ON” and then, turn motor clock wise, wiper is
operating between position of B and position of C
by transfering pole of motor.
Operation of parking mode
1. Parking on the operation with the clockwise : Under
the wiper is operating,switch of wiper is “off” On
the turning,applying the current between contact
point of W of CAM switch and contact point C,
after relay 1 is off, stopping the motor, within
approximately 1 second, relay 2 of CONT is on,
turning motor counter-clockwise, apply the current
between “P” ground of CAM switch and C ground,
and then relay 2 of CONT is OFF, motor can stop.
Operation for washer mode
Turn washer switch on above 0.5 second, after
operation of wiper mode is operating twice, after
operation of parking mode is operating and then motor
is stopped, but if washer switch is on below 0.5 second,
wiper motor is not operating.
Mode operation of limit switch ON
1. Limit switch on: Under wiper is operating while
w i p e r i s o p e r a t i n g , l i m i t s w i t c h i s “ O N ” ,
immediately back to the position of parking, and
then stop the motor.
2. Limit switch on at the position of parking.
Though turn wiper switch or intermittent switch
on, motor is not operated.
Description of system operation
1. Turn motor switch on, after relay 1 of controller is
on, turn motor clockwise (operation order: (1)
→
(2)
→
(3)
→
(4))
2. On the turning, Applying the current between
contact point of W of CAM switch and contact point
of C, relay 2 of controller is “OFF” and relay 1 is
“ON” and then, turn motor clock wise. CAM switch
is operating between position of (2) and position
of (4) by transfering pole of motor. (operation order
:(2)
→
(3)
→
(4)
→
(3)
→
(2): motion of cycle)
3. Angle of DSP denote the angle between (1) and
(2) or the angle between (1) and (4).
4. Turning motor from position of (3) to position of
(4), stopping in the position of (1), turning from
position of (3) to position of (2), stop in the position
of (1), namely, as motor is parking, such as below
the picture, contact point of W, C, and P are on
the one line.
YAD9D960
Description of System Operation
Operation for wipping mode
1. Turn switch of wiper on, and then relay 1 of CONT
is on, turn motor with clockwise
2. On the turning, Applying the current between
contact point of W and contact point of C, after
relay 2 of CONT is “OFF” relay 1 is “ON”, turn
motor counter clock-wise.