SRAM FS-RUDY-BSE-A1 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 37

SRAM FS-RUDY-BSE-A1 Скачать руководство пользователя страница 26

26

Bleed Procedure

Hold the damper vertically. Thread the syringe into the top cap bleed

Hold the damper vertically. Thread the syringe into the top cap bleed

port. Inject the oil into the damper assembly.

port. Inject the oil into the damper assembly.

Release the plunger and air will purge into the syringe. Compress and

Release the plunger and air will purge into the syringe. Compress and

release the plunger to inject oil into the damper.

release the plunger to inject oil into the damper.

⚠

CAUTION - EYE HAZARD

Oil can eject from the damper bleed port. Use a shop towel to cover

the bleed port to avoid oil spray in the eyes. Wear safety glasses.

Fully extend the rebound shaft, then remove the bleed syringe from the

Fully extend the rebound shaft, then remove the bleed syringe from the

top cap.

top cap.

Make sure the rebound shaft is fully extended and there is a small

Make sure the rebound shaft is fully extended and there is a small

amount of positive pressure in the system before the syringe is

amount of positive pressure in the system before the syringe is

removed. This prevents air getting back into the damper.

removed. This prevents air getting back into the damper.

Fill the bleed syringe half full with suspension oil. Slowly depress the

Fill the bleed syringe half full with suspension oil. Slowly depress the

plunger to remove any air bubbles from the syringe.

plunger to remove any air bubbles from the syringe.

NOTICE

Only use the syringe included with the RockShox Standard Bleed kit.

Do not use syringes that have been in contact with DOT brake fluid.

DOT brake fluid will permanently damage the damper.

5

6

7

PLUSH 3wt RockShox Bleed Syringe

«
...
24
25
26
27
28
...
»

Содержание FS-RUDY-BSE-A1






































Отзывы:

Нет отзывов