Spypoint IR-10, Руководство пользователя

Страница: 14 / 27

26 27
Lithium battery pack with charger
The camera SPYPOINT IR-10 can be powered by a
rechargeable lithium battery LIT-C-8 (sold separately, refer to
the section « OPTIONS »). This type of battery is less affected
by cold temperatures and lasts up to 3 times more then an
alkaline battery. During the installation of lithium battery, place
the switch inside the battery case to «
RECHARGEABLE
».
12 volts Power
The camera SPYPOINT IR-10 can also be powered from an
external 12 volts DC input. When using a 12 volt connection,
we recommend you to remove the alkaline batteries to prevent
surcharges. To find the accessories available for the 12 volts,
refer to the section « OPTIONS ».
Solar panel
This model also offers the possibility of a connection to a
solar panel SP-12V (sold separately, refer to the section «
OPTIONS ») to
maintain
the charge of the lithium battery
(sold separately, refer to the section « OPTIONS ») or the 12
volt battery (sold separately, refer to the section « OPTIONS
»). During the installation of the rechargeable lithium battery
or 12 volt battery, slide up the switch inside the battery case up
to «
RECHARGEABLE
» to activate the charging system of
the solar panel.
Electricity
The electrical power is recommended for security purposes. It
provides an instant trigger time when a movement is detected.
We recommend to remove the alkaline batteries when this
power is used. Although lithium battery can remain safely
inside the camera and it is ideal in case of a blackout. A 12 volts
DC adapter that can provide a minimum of 800 mA is needed.
(Refer to the section « OPTIONS »)
Note
: when using the electricity power, the « Multi-shot »
mode and the « Delay » between photos are disabled as the
camera starts instantly every time it detects motion. Also, the
imprinting temperature on each picture is disabled.
English
MEMORY CARD
Using a memory card (sold separately, refer to the section «
OPTIONS ») is required to operate the camera SPYPOINT IR-
10. When the camera is « ON » and no memory card is used,
the screen displays « Insert memory card ». The SD slot of
the camera has a 32 GB memory capacity. Before inserting or
removing the memory card, the camera must be turned « OFF
». Failing to do so may cause loss of or damage the pictures
already recorded from the memory card. When the SD card is
full, the viewing screen indicates « Disk Full ». The following
data shows an approximate quantity of photos or video length
that can be taken by the camera depending on the memory card
capacity.
RESOLUTION 2.0 GB 4.0 GB 8.0 GB 32 GB
5 MP
6 MP
8 MP
10 MP
12 MP
1190
952
635
595
476
2380
1904
1270
1190
952
4760
3808
2540
2380
1904
19040
15232
10160
9520
7616
vIDEO RESOLUTION
320 x 240
640 x 480
45 min
30 min
1h30
1h
3h
2h
12h
8h
In « TEST » mode if the SD card is locked in, the screen will
indicate «
Card protect
» and the light in the front of the
camera remains on.
DISTANCE
The « DISTANCE » dial (placed on the right side of the internal
camera) can adjust the sensitivity of the detector. The camera is
equipped with a detector sensitive to infrared. The system will
only detect heat source in motion. The greater the mass of heat,
more sensitive is the system. The range of detection is between
5 and 50 feet. Turn dial up to increase distance. The best way
to adjust the distance is to set the camera in « TEST » mode
(see above). Make sure to have the least possible objects in
front of the camera during the positioning. This will prevent
picture to be taken by the camera when oriented towards the
sun while an object moves in front of the camera (eg. a branch).
English