background image

1008290 Rev. C

10

READ BEFORE USING

Now You Are Ready To Put 
Material In The Hopper

WARNING:

  Avoid Injury!  Chemicals can be 

dangerous.  Avoid injury to operators or bystanders.

•  Make sure the rate gate is in the closed position.

•  Read chemical container label for handling 

instructions.  A Material Safety Data Sheet (MSDS) 
should be supplied by the chemical dealer and 
provides proper safety information.

•  Wear proper clothing and safety equipment while 

handling or applying chemicals.

•  Prohibit all smoking, drinking, and eating around 

chemicals.

•  When spreading products containing herbicides, 

exercise extreme caution with respect to careless 
spreading and to wind-drift.  Contact Of Some 
Products On Some Plants Can Be Fatal.

•  Fill the spreader on a fl at, level surface only.  Fill on 

sidewalk, driveway, cardboard, etc. to avoid material 
loss.

• When 

fi lling hopper with material, always use screen 

to help break up clumps.

Now You Are Ready To Spread

•  Keep spinner blade clean.  Excess material build-up 

can cause an uneven spread pattern.

•  Keep the impeller level when spreading.

•  DO NOT overload.  Maximum capacity is 120 lbs.

•  DO NOT use on windy days.

•  Spread header strips at the ends of the area 

OPPOSITE of the direction of spreading.  This will 
provide a "turn-around" area, an area to re-align the 
spreader for the return spread.

•  Example shown is for 6 ft. wide spread.  Make the 

fi rst spread pass at one-half the spread width from 
the edge of the spreading area or in this case, 
approximately 3 feet (or one big step).

•  Additional spreading passes will be at the full spread 

width or approximately 6 ft. apart.

•  TAKE A SIGHTING AT THE FAR END.  Keep your eye 

on the sighting as you spread.  You will not need 

to wonder where you are or where you have been.  
Continue until spreading is completed.

•  Left over fertilizer can be spread under trees and 

other high feeding areas without showing "edge of 
spread" lines.

Tip:  

When not spreading, and if pushing the spreader 

some distance, tip the spreader so only the idle wheel is 
on the ground.

Header

6’

6’

3’

Header

Cleaning The Spreader Is Part 
Of The Spreading Job

Clean and oil spreader immediately after each use.

Method #1 - Wipe spreader thoroughly with an oily cloth.  
Oil all bearings and bearing areas.

Method #2 - Wash, rinse, and dry the spreader.  Note:  
Drying takes time.  Moisture trapped in bearing areas is 
slow to go.  Immediately after drying - oil all bearings and 
moving parts.  Make certain all operations are thorough.

NOTE:  Good "Dry Cleaning" is preferable to poor "Wet 
Cleaning".

•  It is virtually impossible to have rust and corrosion on 

a clean, dry, oiled surface.

•  Again - just before using - oil all bearings and moving 

parts.

•  In storage, ideally the spreader should be hung by 

the handle.  In any case, do not pile weight on the 
spreader, as excess weight over a period of time can 
distort the tires.

Oil Bearings And All Moving 
Parts

Make sure the spreader is running freely!

Содержание S60-12020













Отзывы: