Read Before Using
Cleaning the Spreader is Part of the Spreading Job.
IMMEDIATELY AFTER USE - CLEAN AND OIL THE SPREADER
• Method #1
- Wipe spreader thoroughly with an oily cloth. Oil all
bearings and bearing areas.
• Method #2
- Wash, rinse, and dry the spreader. Note: Drying
takes time. (Moisture trapped in bearing areas is slow to go.)
Immediately after drying - oil all bearings and moving parts. Make
certain all operations are thorough.
Note: Good “Dry Cleaning” is preferable to poor “Wet Cleaning”
.
• It is virtually impossible to have rust and corrosion on a clean, dry,
oiled surface.
• Again - just before using - oil all bearings and moving parts.
• In storage, ideally the spreader should be hung by the handle. In
any case, do not pile weight on the spreader, as excess weight over
a period of time can distort the tires.
“To Every Action There Is Always An Opposed and Equal Reaction”
(Newton’s law of motion - Sir Isaac Newton, 1642-1727.)
NOTE: With the rotary agitator installed, the rate gate closed (not spreading) and with
material in the hopper, the spreader will push harder than normal. (This is because the
agitator is stirring the material and it has no place to go.)
RECOMMENDATION: When not spreading and the spreader is being
pushed some distance, tip the spreader so only the idle wheel is on
the ground.
3
2
Model 75 Parts List
Item #
Part #
Quantity
Description
1
05-75-7510
1
Hopper
2
05-75-7516
1
Strap Assembly
3
05-75-7544
1
Crank Assembly
4
05-75-7526
1
Sleeve
5
05-75-2015
1
O-Ring
6
05-75-7551
1
Connector
7
05-75-8063
2
Fastex Nut (Bush, RTNR)
8
05-75-7588
2
Bushing (Impeller Shaft)
9
05-75-7507
1
Main Shaft & Gear Assembly
10
05-75-7502
1
Impeller Shaft & Gear Assembly
11
05-75-7552
1
Impeller Shaft Bracket
12
05-75-7548
1
Bushing (Impeller Shaft)
13
05-75-7566
2
Tinnerman Nut
14
05-75-7553
1
Cam
15
05-75-7561
1
50+ Bevel Gear
16
05-75-7525
1
Stub Shaft
17
05-75-7545-B
1
Mounting Bracket (Main Shaft)
18
05-75-7554
1
Base
19
05-75-7546
1
Shutter Bar
20
05-75-7558
1
Pattern Door Guide
21
05-75-7563-A
1
Spring (Shutter Bar)
22
05-75-7563-B
1
Clip (Shutter Bar Spring)
23
05-75-7547
1
Shutter
24
05-75-7570
1
Bracket (Shutter)
25
05-75-7569
1
Shield (Shutter Bar)
26
05-75-7562
1
Spinner
27
SS-91-0004
1
1/4-20 Nylock Nut
28
05-75-7555
1
Shield (Bottom)
29
05-75-7577
1
Spring (Latch)
30
05-75-7575
1
Bolt (Latch 6-32 x 1/2 Carriage)
31
05-75-7519
1
Latch Stop
32
05-75-7529
1
Wing Nut (6-32)
33
05-75-7534
1
Latch Lever
34
05-75-7564
1
Side Shield
35
05-75-7559
1
Pattern Door
36
05-75-7501
1
Base & Gear Assembly
37
05-75-7590
2
Screws (3/8 x 6)
