SPX W+ Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

SPX W+ Скачать руководство пользователя страница 8

4

453343 ISS S 07.2010

Rotating Parts Hazard

Routine cleaning and maintenance procedures require pump disassembly.
The pump contains close fitting parts which rotate during operation. Should
the pump start unexpectedly while disassembled, severe injury could result.

To minimize the risk of this hazard:

1.

Do Not assemble or disassemble the pump

2.

Do Not remove the guard from the adapter

3.

Do Not perform any maintenance or service on the motor or pump

unless the power source has been turned off and Locked Out, where
only the person involved in the maintenance procedure has

possession of the key.

High Temperature Hazard

Some pump applications may require processing of high temperature liquids
and/or the use of high temperature cleaning/sanitizing solutions. Pumping
high temperature liquids is considered to be hazardous and extreme care
should be taken when handling such liquids.

To minimize the risk of this hazard:

1.

All installation, maintenance, and service of piping, valves, and other

controls must be performed by trained and authorized plumbers only.
This applies to process piping and cleaning/sanitizing piping.

2.

All plumbing installation must comply with all applicable codes and

standards including those established by OSHA.

3.

Do Not perform any maintenance or service on the motor or pump

unless the power source has been turned off and Locked Out, where
only the person involved in the maintenance procedure has

possession of the key..

4.

Never disconnect any lines or fittings (whether process or

cleaning/sanitizing) or disassemble the pump until the line is no
longer under pressure and the fluid inside is not hot or harmful.

5

. Operating personnel must be authorized and trained.

Warnings

«
...
6
7
8
9
10
...
»

Содержание W+

























Отзывы:

Нет отзывов