SPX Pearpoint Flexiprobe P340 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 60

background image

Copyright 2012 Radiodetection Ltd.

– SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation.

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection
Ltd. We reserve the right to alter or amend any published specification without notice.

Page 3 of 59

1.

Before you begin

Re-terminations should be performed by a competent technician.

We cannot guarantee or warrant any repairs made by any employee outside of our business,
including other unaffiliated service centres.

It is possible to cause further damage to systems, consequential damage caused by poor
worksmanship will not be covered and the warranty will be considered void. This document is
intended as a guide for customers wishing to re-terminate the reels, however we cannot accept
responsibility for any damages resulting from poor application of our guide.

Due to continuous development of our product details may change.  We only offer this guide to
support those customers who agree to assume responsibility for maintaining their own product.
We can offer training and support packages for customers on how to perform this competently.
Enquire with Sales or Service.

Before any re-termination ensure the system is disconnected from the power supply and

mains to ensure safe working.

The cameras can become hot,

do not look directly into

the camera due to the bright lights, they may cause temporary blindness or longer-term issues.

Potentially hazardous current and voltage sources contained within system when live.

Gloves and other appropriate PPE are strongly advised based on your risk assessment

due to various mechanical, hygienic, electronic and other hazards. If the system is being re-
terminated in a clean area ensure it has been suitably cleaned for the purpose.

Before you attempt any re-termination it is worth checking the video settings are correct for your
reel. For each different length of reel a different amplifier is used to boost the video signal. If this
is set incorrectly it will give a poor signal that may be misinterpreted as a cable fault.

You will need a colour copy of this guide due to colour coded wires and information.

Be aware of and take precautions against ESD. It is advised as part of your risk assessment you
consider the MSDS sheets available online from the 3

rd

party products required for some repair

operations. Consider PPE as part of this review.

Warning

Use extreme caution when using tools or industrial products or preparations.
When using the junior hacksaw, avoid inhaling or ingesting the glass fibre dust. Consider PPE.
When using the epoxy potting compound, avoid contact with skin.

«
1
2
3
4
5
...
»

Содержание Pearpoint Flexiprobe P340





























































Отзывы:

Нет отзывов

Похожие инструкции для Pearpoint Flexiprobe P340

Бренд: Farfisa Страницы: 14

Бренд: Valmet Страницы: 63

Бренд: Unipulse Страницы: 129

Бренд: IDEAL Страницы: 11

Бренд: IDEAL Страницы: 16

Бренд: NCTE Страницы: 10

Richer Bass RB1

Бренд: Laney Страницы: 8

Бренд: Laney Страницы: 16

Бренд: Laney Страницы: 6

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Бренд: Yamaha Страницы: 84

Бренд: Kawai Страницы: 40

Бренд: Gas Data Страницы: 99

Бренд: YOSensi Страницы: 27

Бренд: Hanna Instruments Страницы: 2

Бренд: LORECa Hearing Instrument Страницы: 43

zelsius C5 -IUF

Бренд: Zenner Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды