SPX Pearpoint Flexiprobe P340 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 60

SPX Pearpoint Flexiprobe P340 Скачать руководство пользователя страница 19

Copyright 2012 Radiodetection Ltd.

– SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation.

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection
Ltd. We reserve the right to alter or amend any published specification without notice.

Page 19 of 59

Load a tube of two-part quick set epoxy
resin into an application gun.

Use a needle applicator to pot the
termination PCB into the termination
nut.

Insert the resin into the runner hole in
the PCB until it appears out of the riser
hole.

Ensure that the PCB is level and flush
with the top edge of the termination nut.
Keep the assembly level and allow the
epoxy to settle for 3-5 minutes and top
up if necessary.

Leave epoxy to set for at least 15
minutes, it will cure fully in 24 hours.

Runner
hole

Riser hole

«
...
17
18
19
20
21
...
»

Содержание Pearpoint Flexiprobe P340





























































Отзывы:

Нет отзывов