SPX JEMACO HX101K Скачать руководство пользователя страница 5

Страница: 5 / 24

INSTALLATION

Ambient Air Temperature

Locate the dryer indoors where the ambient air temperature will be between 4

ഒ

and

ഒ

. Intermittent operation at ambient temperatures up to 43

ഒ

will not damage the

dryer but may result in a higher dew point or dryer shutdown due to high refrigerant

discharge pressure (see Field Service Guide).

Do not operate air-cooled dryers at ambient air temperatures below 4

ഒ

. Such operation

may result in low suction pressure, causing freeze-up.

Location and Clearance

Mount the dryer on a level base and bolt down if the base vibrates. If the dryer is air

cooled, install it in a clean, well-ventilated area to reduce fouling of the condenser coils

with dirt and dust. Allow 6inches clearance on the sides and the front of the dryer for

cooling airflow on air-cooled dryers and for service access on air-cooled dryers.

System Arrangement

Liquid water adversely affects dryer performance. To prevent "slugging" the dryer with

liquid water, locate the dryer downstream of an aftercooler and a mechanical separator.

Install drain valves to discharge condensate that collects in these areas.

If the airflow is relatively constant and will not cause short term overloading of the

dryer, it is recommended that the dryer be located downstream of the receiver tank. If the

nature of the application is such that the air demand regularly exceeds the dryer flow

rating, it is recommended that the dryer be located upstream of the receiver.

For safety and convenience, install inlet and outlet shutoff valves and depressurization

valves at the locations indicated. These valves allow the dryer to be isolated and

depressurized for servicing. Bypass piping may be installed around the dryer for

uninterrupted airflow when the dryer is serviced. If the compressed air operation cannot

tolerate undried air for short periods, install a second dryer in the bypass line.

Compressed air systems commonly require filters to remove compressor oils, particulates,

condensed liquids and other contaminants. When an oil-removal filter is used, install the

Goodnal STP ST041 Site Services (Jemaco HXK Series Refrigerated Air Dryers HX76K to HX601K Installation

Q-Pulse Id VM409

Active 29/10/2013

Page 5 of 24

Содержание JEMACO HX101K

























Результаты поиска

Содержание JEMACO HX101K

Отзывы:

Похожие инструкции для JEMACO HX101K

Бренды по названию

Популярные бренды

SPX JEMACO HX101K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание JEMACO HX101K

Отзывы:

Похожие инструкции для JEMACO HX101K

Бренды по названию

Популярные бренды