Table of Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Converting the Gun to Pressure Feed . . . . . . . . . . . . . . . . 3
Connecting the Power Cart . . . . . . . . . . . . . . . . . . . . . . . . 3
Preparing to Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety
This manual contains information that must be read and
understood before using the equipment. When you come to
an area that has one of the following symbols, pay particular
attention and make certain to heed the safeguard.
This symbol indicates a potential hazard that may cause
serious injury or loss of life. Important safety information will
follow.
This symbol indicates a potential hazard to you or to the
equipment. Important information that tells how to prevent
damage to the equipment or how to avoid causes of minor
injuries will follow.
HAZARD: GENERAL — May cause property damage or
severe injury.
PREVENTION:
• Read all instructions and safety precautions before
operating any equipment.
• Comply with all appropriate local, state and national codes
governing ventilation, fire prevention, and operation.
• The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly Part 1910 of
the General Standards and Part 1926 of the Construction
Standard should be consulted.
• This equipment is designed to be used with authorized
parts only. When using this equipment with parts that do
not comply with the minimum specifications and safety
devices of the equipment manufacturer, the user assumes
all risks and liabilities.
• Check all hoses for cuts, leaks, abrasion or bulging of
cover, as well as damage or movement of couplings
before each use. If any of these conditions exist, replace
the hose immediately. Never repair a paint hose.
• Never aim the spray gun at any part of the body.
HAZARD: SKIN BURN INJURY— Heated parts can cause
severe skin burn injury.
PREVENTION:
• Quick-disconnect fittings on the hose and the spray gun
become hot during use. Avoid skin contact with any
quick-disconnect fittings when they are hot. Allow the
quick disconnect fittings to cool before disconnecting the
spray gun from the hose
• The compressor becomes hot during use. Allow the
compressor to cool before touching it.
WARNING
NOTE: Notes give important information that should
be given special attention.
CAUTION
WARNING
2
© SprayTECH Corporation. All rights reserved.
HAZARD: HAZARDOUS VAPORS — Paints, solvents,
insecticides, and other materials may be
harmful if inhaled causing severe nausea,
fainting, or poisoning.
PREVENTION:
• Use a respirator or mask whenever there is a chance that
vapors may be inhaled. Read all instructions with the
mask to insure that it will provide the necessary protection
against the inhalation of harmful vapors.
HAZARD: EXPLOSION — Compressed air has great force
and may cause injury.
PREVENTION:
• The pressure pot assembly is protected from over-
pressurizing by a safety valve. Pull the ring on the safety
valve occasionally to make sure that the valve operates
freely. The valve must be replaced if it does not operate
freely or if it does not release air when the ring is pulled.
• Never modify the pressure pot or the compressor.
• Never connect other air tools to the compressor.
HAZARD: EXPLOSION OR FIRE — Solvent and paint
fumes can explode or ignite causing property
damage and or severe injury.
PREVENTION:
• Exhaust and fresh air introduction must be provided to
keep the air within the spray area free from the
accumulation of flammable vapors.
• Keep the turbine at the maximum distance possible from
the spray area.
• Avoid all ignition sources such as static electricity sparks,
open flames, pilot lights, hot objects, cigarettes, and
sparks caused by connecting and disconnecting power
cords and operating light switches.
• Keep the motor away from spray area to avoid solvent
and paint fumes. Motor contains arcing parts which emit
sparks.
• Fire extinguishing equipment must be present and in
working order.
• The power cord must be connected to a grounded circuit.
• Follow the material and solvent manufacturer's safety
precautions and warnings.
Introduction
The HVLP power cart is designed for use with CAPspray spray
systems. The power cart adds tremendous versatility to an
already complete system. Components of the HVLP power
cart include a power switch, a cart, a pressure pot assembly, a
compressor assembly, a pressure pot inlet, a pressure pot
hose, and a pressure pot outlet.
Pressure Pot Inlet
Pressure Pot Hose
Pressure Pot Outlet
Power Switch
(on back of housing)
Pressure Pot
Assembly
Compressor
Assembly
(inside housing)
Cart
English
