background image

 
  
 

November 15,2018  

 

 

10 

301-147 8’ WHEELCHAIR ACCESSIBLE MGR 

INSTALLATION INSTRUCTION 

 

__6. Attach the MGR support arms (6) to the hub assembly 
(5) by sliding the arm over the tabs on the hub 

(do not attach 

to the side of the tabs

) and secure using 1 1/2” bolts, 3/8 

washers and 3/8” nuts.  

(See Detail D – Previous Page) 

__7. When installing the deck sections (1) make sure NOT to 
place tab on support arm (6) in between the deck sections, tab 
should fit on the inside of the flanged side of the deck.  Also, 
completely install all deck sections and level decks to the 
perimeter ring before tightening the bolts completely. There 
are two different types of decks with this unit, when laying 
them out and assembling the unit be sure to alternate from 
one to the other so that the same decks are placed diagonally. 
When tightening the bolts move around the entire unit and 
tighten them evenly to ensure the deck sections are properly 
aligned and to ensure there are no gaps between the deck 
sections.  Connect the support arm (6) to the deck sections as 
well as the deck sections to each other using 1 1/4” bolts (12), 
3/8 washers and 3/8 nuts. (Refer to 

Detail C

 for connecting 

the support arms to the decks and 

Detail G 

for connecting the 

deck sections) 

USING THE IMAGES TO THE RIGHT, ENSURE THE 
EDGES OF EACH DECK ARE FLUSH TO THE NEXT 
DECK TO PREVENT SERIOUS INUJURY 

__8. Attach the Hub Disk (4) to the deck sections (1) and the 
Hub Assembly (5) by placing hub disk on top of the decks 
over the hub assembly and attach by inserting the 4” carriage 
bolts down through the decks and hub assembly.  Secure from 
the bottom of the hub assembly with 1/2” washers and 1/2” 
lock nut. 

(See Detail E) 

 

 

 

 

Содержание 301-147

















Отзывы: