background image

4

2. SAfETy PRECAUTIONS  (CONTINUED)

CAUTION: 

If you feel any pain or any abnormal sensations, STOP YOUR 

WORKOUT and consult your physician immediately. Work within your 

recommended exercise level. DO NOT work to exhaustion. Before beginning 

any exercise program, you should consult with your doctor. It is recommended that 

you undergo a complete physical examination. 

CAUTION: 

If you select the Reverse direction to start the exercise, please be 

prepared for belt to start in reverse direction. Always start the exercise with your feet 

on the side rails before program starts.

WARNING!

 Heart rate monitoring systems may be inaccurate. Too much exercise 

may result in serious injury or death. If you feel faint, stop exercising immediately. 

Note: This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates, uses and can radiate radio frequency energy and, 

if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If the user desires to correct the 

interference, it is at the user’s own expense. 

WARNING!

  Only  qualified  technicians  should  be  allowed  to  contact  electrical 

components such as circuit boards. Some components carry an electrical charge 

even after use has been discontinued or the product has been unplugged. For 

products with power cords, turn off unit power, wait five minutes, then disconnect 

the power cord from the power socket. For products without power cords, let the unit 

sit without use for five minutes. Only after taking such precautions should covers be 

removed and electrical components be accessed.

• 

Do not attempt to drag or carry this unit by the power cord. Keep the 

power cord away from heated surfaces.

• 

Improper grounding can increase the risk of electric shock. Check with 

a qualified electrician if you are in doubt as to whether the power outlet is  

properly grounded.

• 

Do not attempt to modify the plug provided with this product. Proper pow-

er supply must be provided. If the plug does not fit an outlet, contact a quali

-

fied electrician to inspect or modify power in the facility.

• 

Do not stand on the walk belt when starting the treadmill. Straddle the 

belt with your feet on the right and left landing strips.

• 

Always use the safety key when operating the treadmill.

French speakers, please note the following:

• 

 Please place the sticker (provided in the owner’s manual) on the product 

as shown.

CAUTION: 

If you select the Reverse direction to start the exercise, please 

be prepared for belt to start in reverse direction. Always start the exercise 

with your feet on the side rails before program starts.

Содержание T635M






























































Отзывы: