8
1-800-732-0144
SPORTDOG.COM
9
SAMPLE LAyOUTS
Sample 1: Perimeter
Loop (Single Loop)
The Perimeter Loop
is the most common
layout. This will allow
your dog to freely
and safely roam your
entire property (
2C
).
It can also protect
gardens, pools and
landscaping (
2D
).
D
E
A
C
B
Sample 2 (
2E
): Perimeter Loop Using Existing Fence
(Single Loop)
This layout allows you to include your existing fence as part
of your layout and keeps your dog from jumping out or digging
under it. It reduces the amount of wire which will need to be
buried. From the Fence Transmitter, run the wire to
A, A
to
B,
B
to
C, C
to
D, D
to
E, E
to
A
, twisting the wires from
A
back
to the Fence Transmitter. See the “Install the Boundary Wire”
section for more information on attaching the wire to a fence
(pages 14-15)
.
DOUBLE LOOP (2f, 2G, 2H, 2J)
A Double Loop must be used when you are not establishing the Boundary Area on all sides of your property.
When using a Double Loop, the Boundary Wire must be separated by a minimum of THREE TO FIVE FEET to avoid canceling
the signal. Remember that a Double Loop will require twice as much wire
.
E
F
B
A
D
C
E
F
C
A
D
B
Sample 3: Front or Back Yard Only
(Double Loop)
From the Fence Transmitter, run the
wire to
A, A
to
B, B
to
C, C
to
D, D
to
E,
E
to
f
, make a U-turn and follow your
path all the way back to
A
, keeping
the wire separated three to five feet.
Twist the wire from A back to the
Fence Transmitter.
B
A
3-5'
Sample 4: Front Boundary Only
(Double Loop)
From the Fence Transmitter, run
the wire to
A, A
to
B, B
back to
A
keeping the wire separated three
to five feet. Twist the wire from
A
back to the Fence Transmitter.
E
B
D
C
A
3-5'
Sample 5: Lake Access (Double
Loop)
From the Fence Transmitter,
run the wire to
A, A
to
B
, make
a U-turn and go to
C, C
to
D, D
to
E
, make a U-turn and follow
your path all the way back to
A
keeping wire separated three to
five feet. Twist the wire from
A
back to the Fence Transmitter.
Sample 6: Wire Loop Attached to Existing Fence (Double Loop)
This layout allows you to include your existing fence as part of your layout and keeps your
dog from jumping out or digging under it. It reduces the amount of wire which will need to
be buried. Run the wire from the Fence Transmitter to
A
,
A
to
B
,
B
to
C
,
C
to
D
,
D
to
E
,
E
to
f
, make a U-turn and follow your path all the way back to
A
, keeping the wire separated
three to five feet. Twist the wire from
A
back to the Fence Transmitter. See the “Install the
Boundary Wire” section for more information on attaching the wire to a fence (pages 14-15).
3-5'
E
F
B
A
D
C
__________________________________________________
POSITION THE BOUNDARy WIRE
Lay out the Boundary Wire using your proposed boundary, and test the system
BEfORE
burying the wire or attaching it to an
existing fence. This will make any layout changes easier. Work carefully, a nick in the wire insulation can diminish the signal
strength and create a weak area where your dog can escape.
Running the Boundary Wire parallel to and within five feet of electrical wires, neighboring
containment systems, telephone wires, television or antenna cables, or satellite dishes will cause
an inconsistent signal. If you must cross any of these, do so at 90-degree angles (perpendicularly).
If separating your Boundary Wire by at least five feet from a neighboring containment system’s
wire does not reduce the inconsistent signal, contact the Customer Care Center at 1-800-732-0144.
TO TWIST THE BOUNDARy WIRE (3A)
Twisting the Boundary Wire cancels the signal and allows your dog to cross over that
area without receiving a correction. To ensure the signal is cancelled, it is recommended
that you cut and splice the Boundary Wire between each twisted section. The signal
cannot be cancelled by running the wire through plastic or metal piping. Splicing shielded
cable to the Boundary Wire will also not cancel the signal. Refer to figure on the right for
the correct method for twisting the wire. You can twist your own wire by cutting two equal
lengths of Boundary Wire supplied and twisting them together. Anchor one end of the
wires to something secure and insert the other end in a power drill. Pull the wire taut. The
drill enables you to twist the wire quickly. Twist the Boundary Wire 10 to 12 times per foot
to cancel the signal. Once you have completed your boundary layout, insert the twisted
wire into the transmitter.
TO SPLICE OR REPAIR THE BOUNDARy WIRE (3B)
If you need additional Boundary Wire to expand your wire loop, you will need to splice the wires together. Note the locations
of all splices for future reference. Most Boundary Wire breaks occur at splices.
Strip approximately one-half inch of insulation off the ends of the Boundary Wires to be spliced. Make sure the copper
Boundary Wire is not corroded. If the Boundary Wire is corroded, cut it back to expose clean copper wire.
Insert the stripped ends into the wire nut and twist the wire nut around the wires. Pull on the wires to make sure you have
a strong splice connection. If your splice pulls loose, the entire system will fail. Make sure your splice is secure. For extra
protection, Waterproof Wire Nut Covers have been included. Insert the splice and push the wire nut to the bottom, making sure
the gel covers any exposed wire. Latch the Waterproof Wire Nut Cover securely
(3C
).
S
T
E
P
::
0
3
Boundary Wire
10’
10’
Bur
ied
Ca
ble
90˚
TWISTED WIRES
BOUNDARY WIRE
WATERPROOF SPLICE
CORRECT
INCORRECT
400-1178.indd 8-9
3/5/10 4:28 PM
