14
1-800-732-0144
WWW.SPORTDOG.COM 15
STEP :: 05
PROGRAM THE REMOTE TRANSMITTER
The C Train
™
Remote Transmitter has seven operational modes allowing you to select the best match for your type or style of
training. The Remote Transmitter is factory set to mode 1. There’s also one programming mode: Mode V/T (see Change ID Codes on
page 15).
TO CHANGE THE MODE:
1. Referring to the following table, adjust the Intensity Dial to your desired mode.
2. Turn the Remote Transmitter over.
3. Using a pen or the tine on the buckle of your collar strap, press and release the Mode
Button. When the Mode Button is pressed, the Transmitter Indicator Light will be solid
in color. When it’s released, it will flash the number of times for the mode selected.
For example, if mode 5 is desired, adjust the Intensity Dial to 5. Once the Mode Button has
been depressed, the Transmitter Indicator Light will be solid, and once the Mode Button is
released, the Transmitter Indicator Light will flash 5 times.
MODE
UPPER BUTTON FUNCTION
LOWER BUTTON FUNCTION
SIDE BUTTON FUNCTION
NUMBER
OF DOGS
1*
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Tone only
1
2
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Vibe only
1
3
Dog 1: Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Dog 2: Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Dog 3: Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
3
4
Dog 1: Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Dog 2: Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Dog 3: Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
3
5
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
N/A
1
6
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
N/A
1
7
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Locate Remote Beeper**
1
V/T
(ID CODE)
N/A
N/A
(See STEP 8)
N/A
*
Factory default mode.
** Locate Remote Beeper: The Side Button turns run mode off and locates the Remote Beeper. To enable run mode again, press and
hold the Side Button for 3 seconds.
STEP :: 06
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER
To match the Collar Receiver to work with a new Remote Transmitter or to match a new Collar Receiver to work with your existing
Remote Transmitter:
1. Turn the Collar Receiver off.
2. Press and hold the power button. After the Receiver Indicator Light and the OLED Display have turned off, release the power button.
3. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. Once the Receiver
Indicator Light has flashed 5 times, the Collar Receiver has been matched and will begin flashing as normal. If the Receiver Indicator
Light doesn’t flash 5 times, start over from 1.
NOTE: Your Collar Receiver will need to be in either
Training or C Train
™
modes.
STEP :: 07
PROGRAM THE SYSTEM FOR MULTI-DOG OPERATION
SportDOG
™
Brand Add-A-Dog
™
Collar Receiver(s) must be purchased to train additional dogs (up to 3).
NOTE: Your Collar Receiver will need to be in either
Training or C Train modes.
1. Program the Remote Transmitter to mode 3 or 4 (see page 14).
2. Program the first Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the power button. After the Receiver Indicator Light and the OLED Display have turned off, release the
power button.
C. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. If the Receiver
Indicator Light doesn’t flash 5 times, start over from A.
3. Program the second Collar Receiver using A through C above, but using the Lower Button in place of the Upper
Button.
4. Program the third Collar Receiver using A through C above, but using the Side Button in place of the Upper Button.
STEP :: 08
CHANGE ID CODES
An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each is programmed in 1 of 2,000 ID Codes
from the factory. The C Train system has the flexibility to program two or more Remote Transmitters to the same ID Code,
allowing them to both control one Collar Receiver. There are 64 programmable ID Codes available.
TO MANUALLY PROGRAM A REMOTE TRANSMITTER’S ID CODE FOLLOW THESE STEPS:
1. Turn the Intensity Dial to V/T, and then press and release the Mode Button on the back of your Remote Transmitter. This doesn’t
change the mode, so the current mode will still be active after the ID change is complete.
2. Once the Mode Button is released, the Transmitter Indicator Light will illuminate solid green and stay on for 15 seconds.
3. While the green Indicator Light is on, turn the Intensity Dial to select the 1st digit of the ID and then press and release the Side Button.
The green Indicator Light will flash rapidly confirming selection.
4. Again, while the green Indicator Light is on, turn the Intensity Dial to select the 2nd digit of the ID and then press and release the Side
Button. The green Indicator Light will flash rapidly confirming selection. The 2nd digit is optional and, if not desired, wait until the
green light turns off and refrain from pressing the Side Button.
5. At the end of 15 seconds, or after the second press of the Side Button, the green Indicator Light will turn off and the ID of the unit will
be updated. At this point, the unit will be in the same mode it was in prior to setting the ID.
6. Upon changing the ID Code, you’ll need to match the Collar Receiver to the Remote Transmitter (see STEP 6).
TO RETURN THE UNIT TO THE FACTORY ID FOLLOW THESE STEPS:
1. Turn the Intensity Dial to V/T, and then press and release the Mode Button on the back of your Remote Transmitter. This doesn’t
change the mode, so the current mode will still be active after the ID change is complete.
2. Don’t press any buttons and wait until the green Transmitter Indicator Light turns off.
3. You’ll need to match the Collar Receiver to the Remote Transmitter (see STEP 6).
