1-800-732-0144
14
WWW.SPORTDOG.COM
15
TO MANUALLY PROGRAM THE REMOTE TRANSMITTER’S ID CODE FOLLOW
THESE STEPS:
1. Turn the intensity dial to level 7, flip the toggle switch up, and then press and release
the mode button on the back of your Remote Transmitter. This does not change the
mode, so the current mode will still be active after the ID change is complete.
2. Once the mode button is released, the green indicator light will illuminate and stay
on for 15 seconds.
3. While the green light is on, turn the intensity dial to select the 1st digit of the ID,
using 1-7, and then press and release the side button. The green light will flash
rapidly confirming selection.
4. Again, while the green light is on, turn the intensity dial to select the 2nd digit of the
ID, using 1-7, and then press and release the side button. The green light will flash
rapidly confirming selection. The 2nd digit is optional, and if not desired, just wait
until the green light turns off and refrain from pressing the side button.
5. At the end of 15 seconds, or after the second press of the side button, the green
light will turn off and the ID/frequency of the unit will be updated. At this point, the
unit will be in the same mode it was in prior to setting the ID.
6. Upon changing the ID Code, you will need to match the Collar Receiver to the
Remote Transmitter. See Step 5.
NOTE: If you press the side button only once (skipping Step 4) the ID is still a two digit ID.
The left digit is defaulted to 1. For example, if you selected 6 in Step 3 and pressed the
button only once, the ID you get will be 16.
To return the unit to the factory ID follow these steps:
1. Turn the intensity dial to level 7, flip the toggle switch up, and then press and release
the mode button on the back of your Remote Transmitter. This does not change the
mode, so the current mode will still be active after the ID change is complete.
2. Do not press any buttons and wait until the green indicator light turns off.
3. You will now need to match the Collar Receiver to the Remote Transmitter. See
Step 5.
matCH tHe CoLLar reCeIVer anD remote tranSmItter
To reset the Collar Receiver to work with a new Remote Transmitter or to reprogram a
new Collar Receiver to work with your existing Remote Transmitter:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn
off after 5-6 seconds. If the On/Off Button is released too early, the Receiver Indicator
Light will begin flashing as normal. If this occurs, start over and repeat from
A
.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator
Light flashes 5 times. You may need to hold both units 2-3 feet from each other before
this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver
has been reset and will begin flashing as normal. If the Receiver Indicator Light does
not flash 5 times, start over and repeat from
A
.
proGram tHe SyStem for tWo-DoG operatIon
SportDOG™ Collar Receivers can be set to respond to either the up or down toggle
switch position. A SportDOG SDR-AH Add-A-Dog
®
Collar Receiver must be purchased to
train a second dog in two-dog mode.
Please refer to the back cover for other compatible
Add-A-Dog Collar Receivers for this system.
TOGGLE SWITCH
1. Program the Remote Transmitter to mode 1 or 2
(see pages 11-12).
2. Then flip the toggle switch to the
up
position to
program the first Collar Receiver.
A.
Turn the Collar Receiver off.
B.
Press and hold the On/Off Button. The Receiver
Indicator Light will come on, then turn off in 4-5
seconds. If the On/Off Button is released too
early, the Receiver Indicator Light will begin its
normal flashing. If this occurs, start over and repeat from
A
.
C.
After the Receiver Indicator Light has turned off, release the On/Off Button.
D.
Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator
Light flashes 5 times. You may need to hold both units 2-3 feet from each other. If the
Receiver Indicator Light does not flash 5 times, start over and repeat from
A
.
3. Program the second Collar Receiver the same way using
A
through
D
above, but
with the toggle switch in the
down
position.
S
T
E
P
::
0
5
S
T
E
P
::
0
6
400-1199.indd 14-15
8/13/10 3:50 PM
