SPL Transient Designer 9842 Скачать руководство пользователя страница 16

Страница: 16 / 18

Transient Designer

Input & Output

Instrumentation amplifier, electronically balanced (differential),
transformerless

Nominal input level ...................................... +6 dB

Input impedance .......................................... = 22 kOhms

Output impedance ...................................... < 600 Ohms

Max. input level .............................................. +24 dBu

Max. output level .......................................... +22,4 dBu

Minimum load ohms ................................... 600 Ohms

Relay Hard Bypass ........................................ yes

Power Fail Safety ........................................... yes

Measurements

Frequency response ..................................... 20 Hz - 100 kHz

... (100 kHz = -3 dB)

CCMR (common mode rejection) ............. - 87 dBu @ 100 Hz

... - 80 dBu @ 1kHz

.. - 75 dBu @ 10 kHz

. - 70 dBu @ 20 kHz

THD & N ............................................................ 0,004 % @ 1kHz

S/N CCIR 468-3 .............................................. -89 dBu

S/N A-weightened ....................................... -105 dBu

Power Supply

Torroidal transformer ................................... 15 VA

Fuse ................................................................... 315 mA

Ground-Lift switch ....................................... yes

Voltage selector ............................................. yes

Dimensions

Housing ............................................................ Standard EIA 19 "/1U,

482 x 44,45 x 237 mm

Weight .............................................................. 3,4 kg

Note: 0 dBu = 0.775 V.

Subject to change without notice.

Specifications

Содержание Transient Designer 9842



















Результаты поиска

Содержание Transient Designer 9842

Отзывы:

Похожие инструкции для Transient Designer 9842

Бренды по названию

Популярные бренды

SPL Transient Designer 9842, Руководство пользователя

Результаты поиска

Содержание Transient Designer 9842

Отзывы:

Похожие инструкции для Transient Designer 9842

Бренды по названию

Популярные бренды