Spitwater 10-120H Скачать руководство пользователя страница 7

 

 7 

4.  EXTENSION CORD 

  If using an extension cord make sure it is according to cross section / maximum length 

requirements as shown to the right. 

  Inadequate extension cords can be dangerous. If an extension cord 

is used, it shall be suitable for outdoor use, and the connection has 
to be kept dry and off ground. It is recommended that this is 
accomplished by means of a cord reel which keeps the socket at 
least 60mm above the ground. 

  Make sure the extension cord is fully 

unrolled, kept dry, away from traffic, 
sharp edges and heat to avoid damage 
or cuts. 

  If using an extension cord make sure it 

is not connected to mains voltage when 
connecting / disconnecting to the unit's 
power cord.  

 

5.  TRIP HAZARD 

  Loose extension cords and power cables provide a potential trip 

hazard, especially when they cross pathways. 

 

Take safety measures like placing traffic cones along the cord or 
tape the cord to the floor with duct tape

.  

 

6.  FIRE PREVENTION AND HOT SURFACE CAUTION 

  Store flammable fluids in approved containers and cabinets away 

from sparks and heat. 

  To avoid fire, be alert for leaks of flammable substances from hoses 

and lines. 

  The exhaust gases and chimney are very hot. To prevent a fire, do 

not expose dry grass, mowed grass, oil or any other combustible 
material to exhaust gas. Be cautious, to avoid burns. 

  Be sure to stop the unit before cleaning the unit. 

  Under NO circumstance use flammable liquids, undiluted acids or 

solvents  as  a  chemical  as  the  spray  produced  would  be  highly 
flammable. 

 

7.  EXHAUST & FLUE GASES 

  Unit exhaust fumes can be very harmful if allowed to accumulate. 

Be sure to run the unit in a well ventailed loaction and where there 
are no people or live stock near the unit. 

  Ensure that any exhaust emissions are not in the vicinity of air 

intakes. 

 

8.  SAFE HANDLING OF FUEL AND LUBRICANTS 

  Always turn off the unit and let the unit cool down before refueling 

and/or lubricating. 

  DO NOT smoke or allow flames or sparks, when fuel is added. 

Fuel is extremely flammable and explosive under certain 
conditions. 

 

60mm
MIN

.

 

 

 

 

 

 

 

 

 

 

 

 

Содержание 10-120H
























Отзывы: