background image

Page 18

Specifications

Noise 

Measured RMS, 22Hz to 22kHz Bandwidth. Inputs at unity gain and terminated 150

W

Output Noise 

24 inputs routed, sends down, master @ unity 

< -80dBu 

EIN 

Mic EIN @ max. gain (150

W

terminated) -129dBu 

THD+N 

Mic sens. -10dBu, Faders @ unity, send at max., 

+20dBu at all outputs @ 1kHz 

<0.005% 

Crosstalk (@1kHz) Typical 

Channel send range 

>90dB

Channel fader range 

>80dB

Mute attenuation 

>100dB

Adjacent output isolation 

>90dB 

CMRR 

Typical at max gain @ 1kHz 

>85dB 

Typical at any gain @ 50Hz 

>65dB 

Frequency Response 

Input to output, medium gain, via output (Hi-pass filter off) 

15Hz to 45kHz 

<-3dB 

25Hz to 25kHz 

<-1dB 

Typical Input and Output levels 

Maximum output 

>+22dBu 

Maximum signal into mic input 

+28dBu 

Maximum signal into FX return & insert return 

+22dBu 

Maximum sensitivity of FX return (Output faders @ unity) 

-15dBu 

Maximum level into Talkback mic input 

+3dBu 

Maximum level into House mic input 

+8dBu 

Headphones (@ 200

W

) 150mW 

Input and Output Impedance 

Mic Input 

1.8k

W

FX returns 

8.6k

W

Monitor Outputs, Wedge & Inserts 

75

W

dim. ’x’

dim. ’y’

Console

24 channel

32 channel

40 channel

1200.6 mm
(47.27")
1454.6 mm
(57.27")
1708.6 mm
(67.27")

1116.6 mm
(43.96")
1370.6 mm
(53.96")
1624.6 mm
(63.96")

dim ’x’

dim ’y’

87.5 mm

(3.44")

Width without end trim

(for flight case mounting)

590.5 mm

(23.25")

Dimensions

Содержание Monitor 2




















Отзывы: