Spirax Sarco DP27 Скачать руководство пользователя страница 8

Страница: 8 / 40

IM-P470-03

CH Issue 7

Pressure bar g

ure

°C

DP27G

and

DP27GY

Pressure bar g

ure

Steam

saturation

curve

2.3 Pressure / temperature limits

Pressure bar g

ure

°C

Steam

saturation

curve

DP27,

DP27E,

DP27R

and

DP27Y

DP27E

The product

must not

be used in this region.

The product should not be used in this region or beyond its operating range as

damage to the internals may occur.

A-D-E

Screwed and flanged EN 1092 PN25, ASME 300 and BS 10 Table H

A-B-C

Flanged ASME 150.

F-F-E

The DP27G and DP27GY are limited to 120 °C.

G-G

The DP27E is limited to 10 bar g @ 190

°C.

Note:

DP27

has a variable rate conical pressure adjustable spring fitted providing a downstream

pressure range of 0.2 - 17 bar g.

DP27Y

has a pressure spring with a range of 0.2 - 3 bar g.

DP27R

Maximum downstream reduced pressure 15 bar g. The control pressure signal to

the pilot diaphragm must be approximately 0.7 bar above the required reduced downstream

pressure.

Содержание DP27









































Результаты поиска

Содержание DP27

Отзывы:

Бренды по названию

Популярные бренды

Spirax Sarco DP27, Инструкция по установке и обслуживанию

Результаты поиска

Содержание DP27

Отзывы:

Бренды по названию

Популярные бренды