Spirax Sarco CA44 Скачать руководство пользователя страница 4

IM-P148-37 

 ST Issue 3

4

1.12 Handling

Manual handling of large and / or heavy products may present a risk of injury. Lifting, 

pushing, pulling, carrying or supporting a load by bodily force can cause injury 

particularly to the back. You are advised to assess the risks taking into account the 

task, the individual, the load and the working environment and use the appropriate 

handling method depending on the circumstances of the work being done.

1.13  Residual hazards

In normal use the external surface of the product may be very hot. If used at the 

maximum permitted operating conditions the surface temperature of some products 

may reach temperatures in excess of 400°C (752°F).

Many products are not self-draining. Take due care when dismantling or removing 

the product from an installation (refer to 'Maintenance instructions').

1.14 Freezing

Provision must be made to protect products which are not self-draining against         

frost damage in environments where they may be exposed to temperatures below 

freezing point.

1.15 Disposal

Unless otherwise stated in the Installation and Maintenance Instructions, this         

product is recyclable and no ecological hazard is anticipated with its disposal     

providing due care is taken, EXCEPT:

Viton - CA44 and CA46 main valve cone:

- Waste parts can be landfilled, when in compliance with National and Local regulations.
- Waste parts can be incinerated, but a scrubber must be used to remove Hydrogen

  Fluoride, which is evolved from the product and with compliance to National and

  Local regulations.
- Parts are insoluble in aquatic media.

1.16  Returning products

Customers and stockists are reminded that under EC Health, Safety and Environment 

Law, when returning products to Spirax Sarco they must provide information on             

any hazards and the precautions to be taken due to contamination residues or 

mechanical damage which may present a health, safety or environmental risk. This 

information must be provided in writing including Health and Safety data sheets 

relating to any substances identified as hazardous or potentially hazardous.

Содержание CA44

















Отзывы: