manualshive.com logo in svg

SpinCore Technologies DDS-I-300, Руководство пользователя

Поделиться
Скачать
SpinCore Technologies DDS-I-300 Скачать руководство пользователя страница 20

PulseBlasterDDS-I-300

IV. PCI Connection - Connecting to the 
PulseBlasterDDS-I-300-PCI boards

Connector Information

There are two main connector types on the PulseBlasterDDS-I-300 PCI board: the BNC connectors and the IDC 

headers – see Figure 11 below.  BNC connectors are mounted on the PCI bracket and are available outside of the 
computer.  The IDC connectors are mounted on-board and are available inside the computer only.  There are two long IDC
headers and one short IDC header.

BNC Connectors

The four BNC connectors provide the primary output interface of the PulseBlasterDDS-I-300 PCI board.  All connectors 

are impedance matched to 50 Ω.  BNC2 is the Analog Output port.  BNC1 and BNC0 are both general purpose digital 
outputs which can be controlled through the pulse program.  BNC3 is not used for the PulseBlasterDDS-I-300.

The analog output connector (BNC2), is not equipped with an interpolating filter.  This allows for maximum flexibility in 

output frequency, but it means that the output may appear quantized if no filter is used on the output.  To eliminate this 
behavior and obtain a smooth RF pulse, the user may filter the output with a bandpass or lowpass filter which will cut off 
the undesired frequency components above the intended RF signal.

Long IDC Headers

There are two long (2x13 pins) IDC headers on the PulseBlasterDDS-I-300 PCI board.  The headers provide access to 

all 24 bits of the flag word, nine of which are available to the user as general purpose digital outputs.  These are labeled 
Flag0..11_Out and Flag12..23_Out.  On each IDC header the top row of pins (14-26) are grounds, and the signals are 
carried on pins 1-13.

http://www.spincore.com

                           20

2017-11-14

Figure 12:

 IDC header pinout.

14 15 16 17 18 19 20 21 22 23 24 25 26

 1  2  3  4  5  6  7  8  9 10 11 12 13

Figure 11:

 PCI Board Connector Locations.

IDC Headers 

BNC3 (Not Used)

BNC1 (Digital Out)

BNC0 (Digital Out)

Hardware Trigger/Reset 

(Digital Out) 

BNC2 (Analog Out)

IDC Headers 

Flag0..11_Out

Flag12..23_Out

Содержание DDS-I-300






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды