Speedsignal RunLock B-339VW04 Скачать руководство пользователя страница 2

B-339VW04_R2 

15.05.2020 

Seite 

2

 von 

12

 

Sicherheitshinweise

 

– safety instructions

 

Der Einbau dieses Artikels darf nur von geschultem Fachpersonal vorgenommen werden und nur nach der in dieser 

Anleitung beschriebenen Vorgehensweise. 

Die speedsignal GmbH übernimmt keinerlei Haftung für Personen- oder Sachschäden, die mit dem Missbrauch unse-

rer Produkte im Zusammenhang stehen.  

Vor der Montage bitte die Batterie abklemmen. Beim Einbau müssen alle zusätzlichen Versorgungsleitungen ent-

sprechend ihres Querschnittes und ihrer Kabellänge abgesichert werden. (DIN VDE 0298-4) 

 

The installation of this product should only be carried out by trained specialist personnel and in accordance with this manual. 

speedsignal GmbH cannot accept any liability for injury to persons or damage to property from errors or mistakes in this operat-

ing manual. 

 

Please disconnect the battery before you start with the installation. During montage, all additional supply lines must be se-

cured pursuant to their cross section and cable length. (DIN VDE 0298-4) 

 

Beschreibung

 

– description

 

Die 

Motorweiterlaufschaltung

 ist eine elektrische Schaltung bei Kraftfahrzeugen, die es ermöglicht, das Fahrzeug bei 

laufendem Motor zu verlassen. Eine Fremdnutzung wird durch Sicherheitsmaßnahmen ausgeschlossen. Zusätzlich 

kann das Fahrzeug bei laufendem Motor von außen verriegelt werden. 
Die Motorweiterlaufschaltung ist in erster Linie für Behördenfahrzeuge in Ausübung ihrer dienstlichen Pflicht vorge-

sehen. Beim Einbau in andere Fahrzeuge als Behördenfahrzeuge weisen wir darauf hin, dass ein unnötiges Laufenlas-

sen von Fahrzeugmotoren nach §30 I StVO verboten ist. 

 

The RunLock is an electrical circuit in motor vehicles that makes it possible to leave the vehicle while the engine is running. Safe-

ty measures prevent unauthorized use. In addition, the vehicle can be locked from the outside while the engine is running. 

 

Primarily it is intended for the use within authority vehicles in exercise of their duties.  

For the installation into other vehicles (not authority) we point out that an unnecessary engine run is forbidden by law in many 

countries such as in Germany according to StVO §30. 

 

Lieferumfang 

– scope of delivery

 

 

 

 

 

 

 

Interface 

Runlock-Schaltung (MWS) Kabelsatz mit Zusatzkabel 

RunLock- Taster 

 

RunLock cable set universal

 

RunLock- button

 

3470079 

C-3470078 

6003131 

 

Benötigtes Werkzeug 

- Required tools 

 

 

 

Torx Schrauber 

Ausbauwerkzeug 

Bohrmaschine 

Lötkolben 

Torx screwdriver 

removal tool 

drill 

soldering irons  

 

Ø 12mm 

Torx 20 

Содержание RunLock B-339VW04













Отзывы: