Spectrum Mopit 3.0 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 27

Spectrum Mopit 3.0 Скачать руководство пользователя страница 19

Page 19

MAINTENANCE / SERVICE

Replacing The Water Solenoid

Rarely the water solenoid may need to be replaced. If your fresh water
leaks out of the Mopit when not being used, or if no water will flow out
of the Mopit even when the brush and solution switches are on, and the
manual water valve is on (pg 6), you may need a new solenoid. You will
need a Phillips screwdriver to replace the solenoid.

1.

Follow steps on page 9 to remove squeegee assembly

2. Disconnect the two electrical plugs going to the solenoid

3. Shut off the manual water valve (pg 6)

4. Remove the white silicone hose going to the solenoid. You can sim-

ply pull it off with your fingers

5. Remove the two Phillips screws holding the solenoid to the base

plate

6. Disconnect the clear

tubing at the first
elbow

7. Installation is the

above steps in re-
verse.

HINT:

If you cut the

wire tie holding the sole-
noid wires to the sole-
noid, replace it.

«
...
17
18
19
20
21
...
»

Содержание Mopit 3.0




























Отзывы:

Нет отзывов