Spectrum Mopit 3.0 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 27

Spectrum Mopit 3.0 Скачать руководство пользователя страница 13

Page 13

MAINTENANCE / SERVICE

Cleaning The Recovery Tank

If the recovery tank is not cleaned out regularly the Mopit will begin to
stink when used. To clean, remove the clean out access cap by twisting
it counterclockwise. Open the drain hose and place it over a floor drain.
Use a hose with a sprayer to spray out the recovery tank. Spray the
Vacuum ball screen. It may also
help to back flush the drain
hose.

After spraying out the tank, use
a trigger sprayer to spray undi-
luted bleach all over the inside
of the recovery tank. Let the
tank sit with the clean out cap

and drain hose cap off until
the inside of the recovery
tank is dry. If your machine
still has a foul odor place 3
ounces (3 measuring cups) of
Mopit cleaning solution into
the recovery tank and then
fill the recovery tank with
water. Let it sit for a few
minutes and then drain the
tank.

Vacuum ball screen

Scan this QR code with your smart phone to watch how to
clean the recovery tank. You can view all of our Mopit mov-
ies on the “Mopit Channel” at www.youtube.com.

«
...
11
12
13
14
15
...
»

Содержание Mopit 3.0




























Отзывы:

Нет отзывов