Spectrum DSM2 Скачать руководство пользователя страница 21

17

18

Warranty and Follow-Up Procedures

Warranty Period:

 

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) 

warranties that the Products purchased (the “Product”) 

will be free from defects in materials and workmanship 

at the date of purchase by the Purchaser. 

Limited Warranty

 

(a) This warranty is limited to the original Purchaser 

(“Purchaser”) and is not transferable. REPAIR OR  

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY 

IS THE EXCLUSIVE REMEDY OF THE PURCHASER.  This 

warranty covers only those Products purchased from an  

authorized Horizon dealer. Third party transactions are 

not covered by this warranty. Proof of purchase is re-

quired for warranty claims. Further, Horizon reserves the 

right to change or modify this warranty without notice 

and disclaims all other warranties, express or implied. 

(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT 

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE  

PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE 

DETERMINED THAT THE PRODUCT WILL SUITABLY 

MEET THE REQUIREMENTS OF THE 

PURCHASER’S INTENDED USE.   

(c) Purchaser Remedy- Horizon’s sole obligation hereun-

der shall be that Horizon will, at its option, (i) repair or 

(ii) replace, any Product determined by Horizon to be 

defective. In the event of a defect, these are the  

Purchaser’s exclusive remedies. Horizon reserves the 

right to inspect any and all equipment involved in a 

warranty claim. Repair or replacement decisions are 

at the sole discretion of Horizon. This warranty does 

not cover cosmetic damage or damage due to acts of 

God, accident, misuse, abuse, negligence, commercial 

use, or modification of or to any part of the Product. 

This warranty does not cover damage due to improper 

installation, operation, maintenance, or attempted repair 

by anyone other than Horizon. Return of any goods by 

Purchaser must be approved in writing by Horizon 

before shipment.

Damage Limits:

 

HORIZON SHALL NOT BE LIABLE FOR SPECIAL,  

INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF 

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN 

ANY WAY CONNECTED WITH THE PRODUCT, WHETHER 

SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, 

NEGLIGENCE, OR STRICT LIABILITY. Further, in no event 

shall the liability of Horizon exceed the individual price of 

the Product on which liability is asserted. As Horizon has 

no control over use, setup, final assembly, modification 

or misuse, no liability shall be assumed nor accepted for 

any resulting damage or injury. By the act of use, setup 

or assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared to  

accept the liability associated with the use of this  

Product, you are advised to return this Product 

immediately in new and unused condition to the place  

of purchase.

Law: 

 These Terms are governed by Illinois law (without 

regard to conflict of law principals).    

Safety Precautions:

 

This is a sophisticated hobby Product and not a toy. It 

must be operated with caution and common sense and 

requires some basic mechanical ability. Failure to 

operate this Product in a safe and responsible  

manner could result in injury or damage to the Product 

or other property. This Product is not intended for use 

by children without direct adult supervision. The Product 

manual contains instructions for safety, operation and 

maintenance. It is essential to read and follow all the 

instructions and warnings in the manual, prior to  

assembly, setup or use, in order to operate correctly 

and avoid damage or injury.

Questions, Assistance, and Repairs:

 

Your local hobby store and/or place of purchase can-

not provide warranty support or repair. Once assembly, 

setup or use of the Product has been started, you must 

contact Horizon directly. This will enable Horizon to  

better answer your questions and service you in the 

event that you may need any assistance. For questions 

or assistance, please direct your email to  

[email protected], or call 

877.504.0233 toll free to speak to a service technician.

Inspection or Repairs

 

If this Product needs to be inspected or repaired, please 

call for a Return Merchandise Authorization (RMA). Pack 

the Product securely using a shipping carton. Please 

note that original boxes may be included, but are not 

designed to withstand the rigors of shipping without  

additional protection. Ship via a carrier that provides 

tracking and insurance for lost or damaged parcels, 

as Horizon is not responsible for merchandise until it 

arrives and is accepted at our facility. A Service Repair 

Replacement Parts

Make sure that you keep your Radian flying. Replacement parts are available at your local hobby shop or from 

Horizon Hobby (www.horizonhobby.com). Please try your local hobby shop first. By supporting them, they will be 

there when you need them.

Item #: 

Description:

PKZ1017 

Propeller Blades: Radian

PKZ1018 

Prop Adapter & Spinner Set: Radian

PKZ1033 

11.1V 1300mAH LiPo Battery

PKZ1040 

2-3 DC LiPo Balancing Charger

PKZ1060 

SV80 3-Wire Sub-Micro Servo 

PKZ4703 

Decal Sheet: Radian

PKZ4713 

Canopy: Radian

PKZ4714 

Firewall w/Screws: Radian

PKZ4716 

PKZ 480 Outrunner Brushless Motor: Radian

PKZ4720 

Main Wing with Spar: Radian

PKZ4722 

Pushrods with Clevis: Radian

PKZ4725 

Tail Wing Set: Radian

PKZ4767 

Bare Fuselage: Radian

SPMAR500 

DSM2 5CH Sport Receiver

EFLA1030 

30-Amp Pro SB Brushless ESC

Option Parts
Item #: 

Description:

EFLB12503S 

11.1V 1250mAh Li-Po Battery

EFLC505 

1-5 Cell Li-Po Charger with Balancer

HBZ6513 

Alligator Clip: 12V Adapter

THP1205P 

AC to 12VDC, 5.0A Power Supply: EFLC505

SPMP300 

Spektrum Neck Strap

SPM9525 

Spektrum 1500mAh Ni-MH AA (4)

SPM9526 

Spektrum 150mA Wall Charger 

Register your product and receive ParkZone updates at www.parkzone.com

Содержание DSM2



























Отзывы: