Spectris 04416001A Скачать руководство пользователя | Manualshive

Страница: 99 / 124

background image

SERVO

PRO NANOCHROME Gas

Analyser

98

04416001A / Revision 7

6.1.4 Stand-alone PC with Secondary chassis electrical connections

Figure 49 shows how to connect an analyser supplied as a stand-alone PC with a
secondary chassis. Connections must be connected to a power source using
properly rated cables (see section 3.12). The stand-alone PC must always be
connected to the same protective earth as the secondary chassis of the system.

If an auxiliary oven is supplied, connect the cable coming out of the auxiliary
oven to the connector named

“Auxiliary

O

ven”

on the stand-alone PC. The cable

carries the power supply and the temperature measurement.

The stand-alone PC communicates with the secondary chassis using a RS-232
port. Connect the

port “To analyser” on the PC to the

RS-232 port on the

secondary chassis (see Figure 49).

Figure 49 : Stand-alone PC with secondary, electrical connections

«
...
97
98
99
100
101
...
»

Содержание 04416001A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 04416001A

Бренд: UEi Страницы: 4

Бренд: Keithley Страницы: 32

Бренд: Halcyon Страницы: 36

TEC SourceMeter 2510

Бренд: Keithley Страницы: 244

Бренд: Kawai Страницы: 112

Бренд: KROHNE Страницы: 34

Бренд: Yamaha Страницы: 48

Vortex Flow Industry

Бренд: Grundfos Страницы: 16

Бренд: Spacelabs Страницы: 156

Бренд: Stübbe Страницы: 12

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

Бренд: Omega Страницы: 24

Бренд: OrienTek Страницы: 2

Бренд: MEWOI Страницы: 21

Бренд: ATI Technologies Страницы: 4

Бренд: OrienTek Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды