manualshive.com logo in svg

SpectraPure MaxPure MPRO-300 RO System, Инструкция по установке и эксплуатации

Поделиться
Скачать
SpectraPure MaxPure MPRO-300 RO System Скачать руководство пользователя страница 6

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

6

CHECKING THE CONCENTRATE TO PURIFIED WATER RATIO:

This procedure will assure you of maximum life and reliability of your SpectraPure System.  
Failure to perform this procedure can permanently damage the membrane and will void 
the pro-rated Membrane Warranty.

In order to maximize the life of your SpectraPure RO Membrane, you may need to adjust 
the ratio of the concentrate to purified water. If not enough concentrate is allowed to flow 
past the membrane during operation, the impurities will precipitate out on the membrane 
surface, clogging the RO Membrane. To keep this from happening, the Concentrate to Puri-
fied Water Ratio must be checked and adjusted in order to compensate for pressure and 
temperature variations that exist in all water supplies. The flow rate of the concentrate must 
be a minimum of 3X the product flow rate. 3X to 5X is an acceptable concentrate flow rate.

Procedure:
 

1.  Locate the Yellow waste line. Direct the waste line into a sink drain. 

 

2.  Locate the Blue product line . Direct the product line into a sink drain. 

 

3.  Turn on the Feed Supply Valve and let the system run for 20 min.

 

4.  Collect product water from the blue line into a measuring  cup for one 

 

 

minute.  Measure the collected amount 

in milli-liters

.  (30 ml = 1 oz) Do 

 

 

the same with the waste water.

   

WASTE 

IN 

MILLILITERS______________ML

DIVIDED BY

   

PRODUCT 

IN 

MILLILITERS______________ML

             The resultant is the Concentrate to Product Ratio

(Although not needed in this procedure, the daily product  flow rate in Gallons per 

Day (GPD) can be calculated to be equal to the product flow rate times 0.38 ).

 

5.  If ratio is 

less than 3:1= 

Remove Flow Restrictor as shown on page 8-9 and

  cut 

1” 

off.

 

6.  Re-measure your ratio and repeat proceedure untill you acheive a 3/1 ratio.

 

7.     If ratio is 

greater than 5:1

, flow restrictor requires replacement

 

        (Please contact SpectraPure Inc for a longer FR)

Содержание MaxPure MPRO-300 RO System

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды